To Next Page
P
Paul CamachoSep 6, 2025
How to setup Yamaha 5CSMH Outboard Motor tachometer to show the oil pressure?
- BBenjamin SuarezSep 6, 2025
Select the oil press. display.
How to setup Yamaha 5CSMH Outboard Motor tachometer to show the oil pressure?
Select the oil press. display.
What to do if the Yamaha 5CSMH Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha 5CSMH illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha 5CSMH fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
Why does my Yamaha Outboard Motor fuel management gauge show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting is probably wrong. Fill the tank with fuel, and then set the correct fuel tank capacity.
What to do if my Yamaha 5CSMH speedometer shows the incorrect fuel level?
If the speedometer shows an incorrect fuel level, the fuel sensor selection is likely wrong. You should set up the fuel sensor to the correct resistance.
What does it mean when my Yamaha 5CSMH Outboard Motor gauge shows “----”?
If the gauge shows “----”, it indicates that the digital signal is not being received. Make sure the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha Outboard Motor boat speed and/or coolant pressure gauge does not show?
If the boat speed and/or coolant pressure gauge does not show, it is likely that the optional sensor has not been installed. Install the optional sensor.
What causes Yamaha 5CSMH Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
General| Engine Type | 2-Stroke |
|---|---|
| Starting System | Manual |
| Oil/Fuel Ratio | 50:1 |
| Max. Output | 5 hp |
| Max Power Output | 5 hp |
| Full Throttle RPM Range | 4500 - 5500 rpm |
| Gear Shift | Forward, Neutral |
| Gear Ratio | 2.08 |
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates special precautions that must be taken to avoid damage to the products or other property.
Provides step-by-step instructions for safely uncrating the outboard motor from its steel frame.
Details the process and considerations for correctly mounting the outboard motor onto the boat transom.
Offers guidance on selecting the appropriate propeller based on application, pitch, and boat load for optimal performance.
Provides a table of recommended engine RPM ranges at Wide-Open-Throttle for propeller selection.
Provides guidance on selecting and routing remote control cables, including length considerations and free-play adjustment.
Introduces the multi-function tiller handle, its electrical functions, and available kits for various engines.
Explains the procedures for mounting gauges, including location, clearance, angle, and wiring connections.
Lists the compatible engine models for digital network gauges, including 4-stroke and HPDI engines.
Lists compatible models for the Digital Network Premium Gauge (6Y9 new network system).
Provides guidance on selecting suitable batteries based on engine type, capacity, and CCA rating.
Details recommended battery cable lengths based on applicable models, conductor cross-section, and atmosphere.
Explains battery wiring procedures, including isolator-equipped models and twin engine applications.
Offers a checklist for pre-delivery inspection of outboard motors to ensure customer satisfaction.
Details the components for the immobilizer kit applicable to US, ANZ, and CRB models.
