Yamaha DME64N - User Manual

Other manuals for Yamaha DME64N

Questions and Answers

M
Matthew HarrisonSep 14, 2025
What to do if I cannot recall a scene on my Yamaha DME64N?
- H
  hsuttonSep 14, 2025
  If you cannot recall a scene on your Yamaha Music Mixer, it might be because appropriate scene data has not been stored in the DME64N/24N. Set up and store an appropriate scene in the DME64N/ 24N. Use the DME Designer for scene setup.
C
Cody Farrell MDAug 25, 2025
How to troubleshoot no sound input on Yamaha DME64N Music Mixer?
- P
  Paige CainAug 25, 2025
  Check that the cables are properly connected. Ensure that an appropriate signal is being received from the external device. Verify that the GAIN of the internal (DME24N) or external head amp is set to an appropriate level.
P
Paul ThompsonAug 25, 2025
What to do if my Yamaha DME64N Music Mixer won't turn on?
- M
  Matthew BookerAug 26, 2025
  Check that the power cable is properly connected and that the POWER switch is turned on.
D
Debra FrazierAug 26, 2025
Why are scenes recalled unexpectedly on my Yamaha DME64N Music Mixer?
- A
  Abigail WebbAug 27, 2025
  Check if input is being received from an external device or the DME Designer. Use the DME Designer to check the MIDI Program Change Table settings, the GPI input assignments, and the Remote Control Setup List assignments.
C
Christine SimmonsSep 15, 2025
What to do if user-defined parameters cannot be edited on my Yamaha Music Mixer?
- S
  Stephanie MooreSep 15, 2025
  If user-defined parameters cannot be edited on your Yamaha Music Mixer, the user-defined parameter lock function may be engaged. Disengage the user-defined parameter lock function.
J
jenkinsandrewSep 23, 2025
When an external device is being used as the word clock master and the word clock source is changed, why does noise appear at the analog outputs of my Yamaha Music Mixer?
- C
  Corey KempSep 23, 2025
  This is normal, and can occur when an MY8-AT I/O card is being used. Reduce the volume level of the power amplifier(s) to prevent possible speaker damage, or make sure that the DME64N/24N is off beforehand.
S
Susan KellerSep 7, 2025
What to do if the panel controls don’t work on my Yamaha Music Mixer?
- M
  Miguel MarshallSep 7, 2025
  If the panel controls on your Yamaha Music Mixer aren't working, check these possible causes: * Disengage the Panel Lock function. * Ensure one DME64N/24N is assigned as the zone master for each zone. * Set an appropriate IP address.
T
Thomas NguyenSep 8, 2025
How to establish communication between the DME64N/24N and the DME Designer application software for my Yamaha Music Mixer?
- J
  Jeffrey HernandezSep 8, 2025
  To establish communication between the DME64N/24N and the DME Designer application software on your Yamaha Music Mixer: * Turn the power to the DME64N/24N ON. * Launch the DME Designer application. * Make sure that the connection cable is properly connected.
M
Michael ChambersSep 2, 2025
What to do if I can’t recall the desired scene on my Yamaha DME64N Music Mixer?
- G
  gibsonjenniferSep 2, 2025
  Write the required scene data from the DME Designer to the DME64N/24N.
J
Jonathan SchmidtAug 31, 2025
What to do if I cannot exchange data between the DME64N/24N and the DME Designer of Yamaha Music Mixer?
- S
  Samantha GrayAug 31, 2025
  Check if the network cables are connected correctly, if the USB-MIDI driver has been properly installed, and if the DME-N Network Driver has been properly set up (if using the [NETWORK] connector). Also, verify if a MIDI port has been properly assigned and if you are using a version of DME Designer later than 3.8.