To Next PageTo Next PageHow to stop buzzing noises from Yamaha RX-V1000?
If you're experiencing buzzing and whining noises (especially in the evening) from your Yamaha Receiver: * Move this unit away from the TV, as a TV set may be being used nearby.
Why does Yamaha RX-V1000 remote learning stop?
If continuous functions such as volume adjustment are learned, but operate only for a moment before stopping on your Yamaha Receiver: * Be sure to press and hold the function button on the other remote control until TRANSMIT begins flashing slowly, as the learning process may be incomplete.
How to stop humming sound from Yamaha Receiver?
To eliminate a humming sound from your Yamaha Receiver: * Ensure audio plugs are firmly connected; defective cables may also cause this. * Connect the grounding cord of your turntable to the GND terminal of the unit, if applicable.
Why is there no picture from my Yamaha RX-V1000?
If you're experiencing no picture from your Yamaha Receiver: * Ensure there is an S-video connection between the unit and the video monitor by connecting the monitor’s S-video input jack to the unit’s S VIDEO MONITOR OUT jack, especially if S-video signals are being input to the unit.
General| Type | AV receiver |
|---|---|
| Audio Channels | 5.1 |
| Frequency Response | 20Hz-20kHz |
| Input Impedance | 47k ohms |
| Input Sensitivity | 200 mV |
| Signal to Noise Ratio | 100 dB |
| Channel Separation | 70 dB |
| Video Inputs | Composite, S-Video |
| Surround Sound | Dolby Digital, DTS |
| Speaker Terminals | Binding Posts |
| Power Output (per channel) | 100 W |
| Speaker Load Impedance | 8 ohms |
| Digital Inputs | Optical, Coaxial |
| Audio Inputs | Phono |
Explains symbols used in the manual to alert users to potential hazards.
Provides notices regarding FCC compliance and interference guidelines.
Lists essential safety warnings and precautions before operating the unit.
Details the items included in the product package.
Provides instructions on how to insert batteries into the remote control.
Identifies and describes the buttons and features on the unit's front panel.
Instructions on how to open and close the front panel door.
Introduces the remote control's sections and general layout.
Guidance on operating the unit using the remote control.
Explains the various indicators and information shown on the front panel display.
Details the input and output jacks and terminals on the rear panel.
Guides on selecting and setting up speakers for optimal sound.
Recommendations for positioning speakers for surround sound.
Instructions for connecting various audio and video components.
Details on connecting digital, analog, and turntable audio sources.
Guide to connecting composite, S-Video, and component video sources.
Step-by-step guide for connecting speakers to the unit's terminals.
Instructions for connecting external audio processing units.
Guidance on setting the impedance selector and voltage selector.
Steps for selecting sources, adjusting volume, and basic playback functions.
How to set input priority and select signal modes for various sources.
Guide to choosing and applying different sound field programs.
Explanation of virtual surround sound effects.
Instructions for connecting antennas and tuning radio stations.
Methods for automatically and manually storing radio stations.
Steps for recording audio and video sources.
How to balance speaker output levels using the test tone.
Detailed guide on using the test tone for speaker adjustment.
Instructions for setting and canceling the automatic shut-off timer.
Introduction to the system settings menu and its adjustment.
Configures speaker output modes based on speaker size and configuration.
Sets the output mode for the center speaker.
Sets the output mode for the main left and right speakers.
Sets the output mode for the rear left and right speakers.
Sets the output mode for the rear center speaker.
Determines where LFE and low bass signals are directed.
Adjusts the output level for the main channel speakers.
Adjusts subwoofer output level to match other speakers using test tone.
Adjusts the audio balance between the left and right main speakers.
Adjusts bass and treble levels for headphone listening.
Adjusts the center speaker's tonal quality using a 5-band equalizer.
Allows renaming of input sources for display purposes.
Designates inputs for component and digital jacks.
Sets the input mode for digital sources.
Resets DSP program parameters to their initial settings.
Configures settings specific to Dolby Digital signal decoding.
Adjusts the output level of the LFE channel for Dolby Digital.
Adjusts the dynamic range for Dolby Digital signals.
Adjusts the output level of the LFE channel for DTS.
Enables automatic switching for Dolby Digital Matrix 6.1/DTS ES.
Adjusts delay time for center and rear center channels.
Configures OSD background and brightness.
Protects settings from accidental changes.
Explains advanced remote control functions like Learn and Macro.
Instructions for programming the remote to control other devices.
How to teach the remote new functions using the Learn feature.
Guide to programming and using macro sequences for operations.
Setting up and using the unit for a second audio/video room.
Descriptions of DSP programs for audio sources.
Descriptions of DSP programs for audio-video and movie sources.
Details on DSP programs designed for movie soundtracks.
Explains programs for Dolby Digital and DTS surround sound playback.
Explains the elements that create a sound field.
How to change parameter settings to customize sound fields.
Procedure to restore parameter settings to their original values.
Detailed descriptions of adjustable parameters for sound fields.
Common problems and solutions for unit operation.
Addresses reception problems and station tuning issues.
Solutions for problems with the remote control's functionality.
Technical details for the audio output and processing capabilities.
Technical details for the FM tuner section.
Technical details for the AM tuner section.
Details on power supply, dimensions, weight, and accessories.
Technical details for video input and output signals.
Diagrams of remote control buttons for various components.
Specific remote control button layouts for LD, VCR, CBL/SAT, DVD, TV/LD.
