EasyManua.ls Logo

Yamaha YSP10 - User Manual

Yamaha YSP10
120 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
For Service Engineers
Service Information
1/120
SI1906002J-002 : YSP10 installation and adjustment procedures
MACHINE TYPE : YSP10
CLASSIFICATION : Installation and Adjustment
REFERENCE : SI1004008E: General procedures for
carrying in and installing a machine
YSP10 installation and adjustment procedures
General description
This document describes how to carry in, install, and adjust YSP10.
About this document:
This document is intended for service engineers.
YAMAHA is not responsible for any problems caused by the misuse of the document.
This document contains the method to edit the system data that affects the customer’s machine
condition.
Make sure to thoroughly understand the contents of the document, and perform the adjustments on
your own responsibility.
About the safety:
Strictly follow the safety precautions in the “Safety” section in the “Operation Manual”.
Disclaimers:
This document contains the preliminary information subject to change in the future.
The information contained in this document represents the current view of YAMAHA on the issues discussed as of
the date of issuance. As YAMAHA must respond to changing market conditions, it should not be interpreted to be a
commitment on the part of YAMAHA, and YAMAHA cannot guarantee the accuracy of any information presented
after the date of issuance.
This document is provided for information purposes only, and it is provided without any warranties, either express or
implied.
It is the responsibility of the user to comply with all applicable copyright laws. Without limiting the rights under
copyright, no part of this document may be reproduced, stored in or introduced into a retrieval system, or transmitted
in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), or for any purpose,
without the written permission of YAMAHA.
However, this shall not be construed to limit the user’s right granted by Copyright law.
YAMAHA may have patents, patent applications, trademarks, copyrights, or other intellectual property rights
covering subject matter in this document. Except as expressly provided in any written license agreement from
YAMAHA, this document does not give users any license to these patents, trademarks, copyrights, or other
intellectual property.
The names of actual companies and products mentioned in this document may contain the trademarks of their
respective owners.
No: SI1906002E-002
ISSUED DATE:
September 18, 2019
REVISED DATE: November 4, 202
1

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Yamaha YSP10 and is the answer not in the manual?

Summary

Preparation before Machine Installation

Required Tools and Materials for Installation

Lists essential tools and materials needed for the machine installation process.

Bringing the Machine to the Installation Site

Removing Shipping Brackets from YSP10

Install Packaged Machine Accessories

Connecting Power Cable and Air Hose to Machine

Connect the Power Cable to the Machine

Procedure for connecting the main power cable to the YSP10.

Connect the Air Hose to the Machine

Steps for connecting the compressed air hose to the YSP10.

Machine Power-On and Return-to-Origin Procedure

Turn On Mains Electricity and Air Supply

Steps to turn on power and air supply before machine initialization.

Power On Machine and Perform Return-to-Origin

Procedure to power on the machine and execute the return-to-origin sequence.

Load Board Data and Configure Conveyor Width

Process for loading calibration data and setting the conveyor width.

Line Alignment Procedures for YSP10

Adjust Machine Level and Conveyor Height

Procedure to adjust the machine's horizontal level and conveyor height.

Fasten Levelling Bolts to Secure Alignment

Steps to tighten levelling bolts to lock the machine's position.

Board Transfer Signal Line Connection and Verification

Connect Board Transfer Signal Lines to YSP10

Procedure to connect signal lines between YSP10 and other machines.

Verify Signal Communication to Upstream Machine

Checks to ensure proper signal transfer to the upstream machine.

YSP10 Board Transfer Test Procedure

Post-Installation Adjustments for YSP10

Checking Motor Reference Values

Procedure to verify the motor reference values in CalibSm.

Adjusting CY-Axis Dual Drive Offset

Steps to adjust the dual drive offset for the CY-axis.

Adjusting R-Axis Initial Positions

Guide for setting the initial positions of the R-axis.

Adjusting R-Axis Linearity

Procedure to calibrate the linearity of the R-axis.

Adjusting Board Transfer Positions (Y and Z)

Steps to adjust the Y and Z axis positions for board transfer.

Adjusting Camera Scales and Positions

Calibrating the scale and position of various machine cameras.

Print Feedback Adjustment Procedure

Steps for adjusting print offsets using feedback data.

Procedures After Installation and Adjustment Work

Yamaha YSP10 Specifications

General IconGeneral
BrandYamaha
ModelYSP10
CategoryPrinter
LanguageEnglish