How to fix Yard force SA650B Lawn Mower not docking?
To address docking problems with your Yard force Lawn Mower: 1. Check that the boundary wire under and in front of the charger is in a straight line. 2. Ensure the docking station's position is suitable.
Why is my Yard force Lawn Mower so noisy?
There are several reasons why your Yard force Lawn Mower might be making excessive noise. First, inspect the blade fixing screws and tighten them if they are loose. Also, check the blades for any damage and replace them if needed. Increasing the cutting height may also reduce the noise. If these steps don't help, it's possible that the cutting motor has failed, and you should call after sales service. As an alternative, mow the lawn with an ordinary lawnmower firstly, choosing a cutting height just above the desired cutting height.
What to do if Yard force SA650B runs in circles?
If your Yard force Lawn Mower is running in circles, there are a few things you can check. First, make sure that no power cable runs parallel and close to the boundary wire. Also, check to see if a front wheel is stuck. You can also try setting your docking station and Robotic Mower to the alternative boundary signal. If none of these steps resolve the issue, the driving motor may be damaged, and you should contact customer support.
How to fix Yard force SA650B if it cannot dock?
If your Yard force Lawn Mower is having trouble docking, check that the boundary wire under and in front of the charger is in a straight line. Also, ensure that the docking station's position is suitable as explained in this manual.
What to do if Yard force SA650B returns to docking station immediately?
If your Yard force Lawn Mower remains at or returns to the docking station immediately after pressing START, it might be because the mower has already completed its programmed working time for the day. Another possibility is that the battery is very low.
What to do if Lift-sensor triggered on Yard force SA650B?
If the lift-sensor is triggered on your Yard force Lawn Mower, it could be due to grass that is too high and dense (taller than 60 mm), which may cause the mower to lift. Mow the lawn with an ordinary lawnmower. Also, check that the mower is free from obstructions.
Why Yard force SA650B remains at docking station after pressing START?
Your Yard force Lawn Mower might stay at the docking station after you press START because it has already completed its programmed working time for the day, or the battery is very low. Check these two things to resolve the issue.
What to do if Yard force SA650B Lawn Mower is very noisy?
If your Yard force Lawn Mower is making a lot of noise, here are a few things to check: 1. Make sure the blade fixing screws are tight. 2. Look at the blades for any damage and replace them if needed. 3. If the grass is too high, increase the cutting height. You might need to mow the lawn with a regular lawnmower first, setting it to a height just above what you want.
Illustration of principal functioning parts of the robotic mower.
Autonomous robot for lawn mowing and its purpose.
Detailed technical specifications and performance data of the mower.
Fundamental advice for safe operation and handling of the mower.
Explanation of symbols used in the manual and on the machine.
Safety warnings related to the power supply unit.
Important safety warnings concerning the battery pack.
Further safety guidelines specific to the robotic mower.
Advice on preventing damage from lightning strikes.
Essential steps and precautions for operating the mower.
Steps to take before starting to operate the mower.
Rules for safe operation and use of the mower.
Precautions to take when stopping or pausing operation.
Safety advice related to maintaining the mower.
Critical safety instructions regarding electrical hazards.
Instructions for safely moving the mower.
Steps for safely moving the mower within or between areas.
Guidance on selecting an optimal location for the docking station.
Understanding how the mower interacts with the boundary wire.
Procedures for starting and stopping the mower during operation.
Constraints and considerations for mowing patterns and areas.
Details on cutting height adjustment and blade maintenance.
Keeping the mower in safe working condition through regular checks.
Proper charging and handling of the battery for longevity.
Replacing worn or damaged blades and other parts.
General guidance on checking and cleaning the mower.
Information on the battery's estimated lifespan.
Steps to prepare the mower for winter storage.
Tasks to perform before using the mower after winter.
How to clean the exterior of the mower.
Instructions for cleaning the underside of the mower.
Cleaning charging contacts for efficient charging.
Guidelines for storing the mower for short periods.
Setting up the boundary wire to define the mowing zone.
How the mower detects and reacts to obstacles.
Overview of the installation process and required tools.
How the mower handles obstacles and operational boundaries.
Guidance for installing boundary wire around trees, stones, and slopes.
Guidelines for boundary wire placement near paths and driveways.
Dealing with uneven lawn areas and potential blade contact.
How to exclude flowerbeds using boundary wire techniques.
Importance of excluding pools and ponds from the cutting area.
General rules and best practices for boundary wire installation.
Step-by-step guide to marking the mower's working area.
Boundary wire must form a single, unbroken loop.
Finding the optimal location for the docking station.
How to secure the boundary wire using pegs and proper installation.
Guidance on peg spacing, orientation, and wire securing.
Using alternative fixings for boundary wire on hard surfaces.
Connecting the boundary wire to the docking station.
Preparing wire ends for connection to the docking station.
Steps to turn on and test the complete system.
Understanding the docking station's LED indicators.
How to test the mower's operation after installation.
Explanation of the mower's control panel and its functions.
Procedures for locking and unlocking the control panel.
Steps to unlock the control panel using the PIN.
Manually locking the control panel.
Step-by-step guide to changing the user PIN.
Explanation of the analog keyboard mapping.
Explains the meaning of various status indicator LEDs.
Indicates status of the lift sensor.
Indicates status of the boundary wire signal.
Indicates when the battery charge is low.
Status of the battery charging process.
How to set the daily working hours for the mower.
Table of recommended working times for different lawn sizes.
Setting the boundary signal to avoid interference.
Matching the mower's signal to the docking station's.
Using Home and Start buttons for operation.
Function of the HOME button for recharging.
Function of the STOP button for pausing operation.
How the mower performs edge cutting.
Situations triggering the mower's return to the docking station.
Procedures for reversing or replacing blades.
Information on blade lifespan and inspection.
Step-by-step guide to replacing the battery.
Common issues, solutions, and LED indicators for the docking station.
Common issues and solutions for the Robotic Mower's operation.
Addresses docking failures, erratic motion, noise, and premature returns.
Addresses lift sensor triggers and obstructions.
Resolving issues with the boundary wire signal reception.
Addressing low battery issues and mower behavior.
Troubleshooting charging issues.
Steps to reset the mower to factory defaults.
Manufacturer's declaration of product compliance with standards.
General| Type | Robotic Lawn Mower |
|---|---|
| Cutting Width | 18 cm |
| Cutting Height Adjustment | 20-60 mm |
| Battery Capacity | 2.0 Ah |
| Mowing Area | 650 m² |
| Power Source | Battery |
To Next Page
