EasyManua.ls Logo

Yard Works 60-1769-2 - User Manual

Yard Works 60-1769-2
19 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
60-1769-2
19” Electric
Lawn Mower
OPERATOR’S MANUAL
This symbol on the product’s nameplate
means it is listed by
UNDERWRITERS LABORATORIES INC.
TM
MC
772C0755
(11/04)
YardWorks Canada, Toronto, Canada M4S 2B8
IMPORTANT:
Read safety rules and instructions carefully before operating equipment.

Table of Contents

Questions and Answers

  • W
    William GarciaJul 30, 2025
    Why is my Yard Works Lawn Mower not starting?
    • A
      Angela LongJul 30, 2025
      If your Yard Works Lawn Mower isn't starting, several factors could be at play. First, check if the cord is properly connected to both the motor/blade control, ensuring the cord restraint is close to the control. A defective motor/blade control switch could also be the culprit, requiring replacement. Ensure the extension cord is connected to both the mower and a functioning 110-120 V 60 cycle A.C. power outlet. Lastly, verify that the circuit breaker on the mower or in your house receptacle hasn't tripped; if it has, reset it.
  • F
    Fernando JonesAug 3, 2025
    What to do if the circuit breaker keeps tripping on my Yard Works Lawn Mower?
    • W
      wrobertsAug 4, 2025
      If the circuit breaker on your Yard Works Lawn Mower is tripping, it could be due to a few reasons. The mower might be experiencing too much workload. To resolve this, raise the cutting height, reset the circuit breaker, cut a smaller width of grass, and walk more slowly. Also, ensure that the mower is connected to an outlet fused for 15 amperes. Reset the circuit breaker and try starting the mower again.
  • M
    Marilyn SmithAug 7, 2025
    Why is my Yard Works Lawn Mower vibrating at a higher speed?
    • D
      David WeberAug 7, 2025
      If your Yard Works Lawn Mower is vibrating excessively, the issue might stem from a bent motor shaft or an unbalanced blade. Immediately stop the motor, disconnect the power source, and inspect for any damage. Repair any damage found before restarting the mower. If the vibration continues, it's recommended to take the mower to a service dealer. To address an unbalanced blade, balance it by grinding each cutting edge equally.
  • Z
    zwoodAug 12, 2025
    How to fix a Yard Works 60-1769-2 that is cutting grass unevenly?
    • T
      Todd PayneAug 12, 2025
      Uneven cutting with your Yard Works Lawn Mower can often be attributed to a rough or uneven lawn surface, or an improperly set cutting height. Adjust the wheels to a higher cutting height position. To ensure an even cut, all wheels must be set at the same cutting height.
  • M
    Michael TownsendAug 16, 2025
    Why is my Yard Works 60-1769-2 Lawn Mower so hard to push?
    • E
      Edwin SmithAug 16, 2025
      If your Yard Works Lawn Mower is hard to push, it could be due to high grass, a cutting height that's too low, or the rear of the mower housing and blade dragging in heavy grass. Try raising the cutting height to make it easier to push.
  • E
    Elizabeth HaleAug 21, 2025
    What to do if my Yard Works 60-1769-2 Lawn Mower is not mulching properly?
    • C
      Christina KellyAug 21, 2025
      If your Yard Works Lawn Mower isn't mulching properly, it could be due to wet grass clippings sticking to the underside of the deck. Wait until the grass dries before mowing to resolve this issue.
  • L
    Larry ThomasAug 25, 2025
    How to position the handle on a Yard Works 60-1769-2?
    • A
      alexhaneyAug 26, 2025
      If the handle of your Yard Works Lawn Mower is not in position, it might be because the carriage bolts are not seated in the handle insulators. Adjust the height of the handle and ensure the carriage bolts are properly seated into the handle insulators. Then, tighten the hand knobs.

Summary

IMPORTANT SAFE OPERATION PRACTICES

GENERAL OPERATION SAFETY

Read, understand, and follow all instructions on the machine and in the manual before operating.

Slope Operation Safety Rules

Operate on slopes with extra caution, avoid slopes over 15 degrees, and mow across the face.

Children Safety Precautions

Keep children out of the mowing area and never allow children under 14 to operate.

SLOPE GAUGE GUIDE

UNPACKING AND ASSEMBLY

OPERATING YOUR LAWN MOWER

Cord Connection and Power Source

Select CUL cord, connect to restraint, and plug into a 110-120V AC outlet.

Starting the Motor and Blade

Depress locking button, pull lever to engaged position, and release locking button.

Stopping the Motor and Blade

Release motor/blade control lever; blade continues to rotate briefly after motor stops.

Mowing and Mulching Tips

MAKING ADJUSTMENTS

Cutting Height Adjustment

Resetting the Circuit Breaker

MAINTENANCE PROCEDURES

Blade Maintenance and Care

OFF-SEASON STORAGE

TROUBLE SHOOTING GUIDE

YARDWORKS LIMITED WARRANTY

Yard Works 60-1769-2 Specifications

General IconGeneral
BrandYard Works
Model60-1769-2
CategoryLawn Mower
LanguageEnglish

Related product manuals