Yardbeast YB2090 User Manual

larger
than specified in this manual.
you and the machine at risk.
7. Ke
ep all guards and safety elements
in place and in good condition.
8.
Do not operate this machine while
under the influence of alcohol or drugs.
9.
Never operate this machine without
good visibility or light .
10.
If the engine is hot, do not touch
may cause severe burns.
11.
Do not attempt to move the chipper
while the engine is running .
12.
While feeding material into the
machine, keep your
face and body
behind the discharge zone .
13.
Never attempt to unclog the outlet
or discharge opening while the engine is
running. Turn off the engine and wait
until all moving parts are
at a complete
stop.
14 . If any situations
occur which are not
covered in this manual,
be careful and
use common sense. Swiftly
turn off the
chipper and then
contact us for further
advise on your situation.
Maintenance and Storage
1.
Never tamper with the safety components
recklessly .
Check periodically that they are
functioning properly.
2 . Make sure all screws, bolts
, pins and
cotter pins are in good condition
sure the machine is in safe operating
condition . Also , visually inspect
to check if it is damaged and
determine if
repair is necessary.
than specified in this manual.
Puts
ep all guards and safety elements
in place and in good condition.
Do not operate this machine while
under the influence of alcohol or drugs.
Never operate this machine without
If the engine is hot, do not touch
as it
Do not attempt to move the chipper
While feeding material into the
face and body
Never attempt to unclog the outlet
or discharge opening while the engine is
running. Turn off the engine and wait
at a complete
occur which are not
be careful and
turn off the
contact us for further
Never tamper with the safety components
Check periodically that they are
, pins and
cotter pins are in good condition
to make
sure the machine is in safe operating
the chipper
determine if
3. Grease
the bearing often as
the
maintenance chart (found
avoid premature wear;
it also
corrosion and reduces heat , prolonging its
life.
4.
Before cleaning, repairing or inspecti
the chipper
, stop the engine and
moving parts have stopped.
5 .
Do not change the engine governor
settings or overspeed the same . The
governor controls the maximum safe
operating speed of
the engine
6.
Maintain or replace safety and instruction
labels as necessary.
7.
Follow the instructions in this manual
safely storing this machine
off season
8. Never store the chipper
or
in an enclosed space
where there is
presence of flame, spark or
as water heaters, furnaces,
clothes dryers
etc.
9. Allow machine to cool at
before storing after
shutting it down.
10. Always refer to the
operator
proper instructions for off-
season storage
11. If you need to
empty the
outdoors.
Use proper container when
handling fuels.
12. Observe the rules of
proper disposal laws
and regulations for gas,
fuel, oil,
protect the environment
and your
community.
DO NOT MODIFY ENGINE
To
avoid serious
modify the
engine in any way
7
the bearing often as
instructed by
maintenance chart (found
below) to
it also
protects from
corrosion and reduces heat , prolonging its
Before cleaning, repairing or inspecti
ng
, stop the engine and
check all
moving parts have stopped.
Do not change the engine governor
settings or overspeed the same . The
governor controls the maximum safe
the engine
.
Maintain or replace safety and instruction
Follow the instructions in this manual
for
off season
.
or
fuel container
where there is
pilot light such
clothes dryers
,
least 5 minutes
shutting it down.
operator
manual for
season storage
.
empty the
fuel tank, do it
Use proper container when
proper disposal laws
fuel, oil,
etc. to
and your
DO NOT MODIFY ENGINE
avoid serious
injury, do not
engine in any way
. If you

Yardbeast YB2090 Specifications

General

Brand	Yardbeast
Model	YB2090
Category	Other
Language	English