To Next PageTo Next Page
Need help?Do you have a question about the Yardworks LSS10163-1 and is the answer not in the manual?
Battery requires initial charging cycles to achieve maximum run time and capacity.
The tool will not operate when it is plugged into the charger.
Users must read and understand the owner's manual before using the product to reduce injury risk.
Contact customer support for operating, assembly, parts, or service questions, or for return assistance.
Ensure all users read and understand safety instructions before initial use.
Keep hands and feet away from the cutting tool, especially when switched on.
Follow basic safety precautions to reduce risk of fire, electric shock, and personal injury.
Do not use in rain, damp, or explosive atmospheres. Motors spark.
Avoid loose clothing and jewelry. Wear protective hair covering and footwear.
Always wear safety glasses with side shields or goggles.
Keep hands away from blades to prevent cuts.
Use the product only for its intended purpose.
Switch off the tool before adjusting or cleaning to prevent accidental operation.
Blades continue to move for a few seconds after the tool is switched off.
Do not carry the product with a finger on the switch.
Improper use can damage the tool and cause serious danger.
Check parts for damage, alignment, and binding before each use. Repair or replace damaged parts.
Store the product indoors in a dry location out of reach of children.
Operate only when alert, not tired, or under the influence of drugs or alcohol.
Do not touch blade if it jams on an electrical cord; disconnect power.
Operate the tool only in daylight or good artificial light.
Keep proper footing and balance at all times to avoid overreaching.
Ensure trigger is off and safety button is not pushed when clearing jams.
Keep blades sharp and clean. Keep handle dry, clean, and free from oil.
Ensure children and pets stay at a safe distance from the work area.
Product contains chemicals known to cause cancer, birth defects, or reproductive harm.
Unauthorized modifications can void user's authority to operate equipment.
Equipment tested and found compliant with Class B digital device limits.
Steps to correct harmful interference to radio or television reception.
Indicates precautions involving personal safety.
Read manual and follow warning and safety instructions.
Always wear eye protection when using the tool.
Do not use the tool in rain or electrical storms.
Warning that blades continue to move after switching off.
Warning to keep bystanders away from the work area.
Indicates the battery charger should only be used indoors.
Symbol indicating the battery charger has a safety transformer.
Battery must be fully charged before first use; charging time is 3 to 5 hours.
Use only the supplied charger for the tool's lithium battery.
Tool automatically switches off when battery is flat to prevent deep discharge damage.
Do not continue to use the tool after automatic shut-off; recharge the battery.
Recycle waste electrical products properly according to local guidelines.
Tool operates on 3.6V DC with 1.5 Ah battery capacity.
Tool has a no-load speed of 1000 SPM.
Charger input is 100-120V, 50/60Hz AC.
The tool uses a Lithium-ion battery.
Grass shear blade width is 3.2 inches (80mm).
Shrub trimming blade cutting length is 6.3 inches (160mm).
Maximum cutting diameter for shrub blade is 5/16 inch (8mm).
Features a tool-less system for changing blades.
Item 1 in the parts list: the grass cutter blade.
Item 2: the button used to release the blade.
Item 3: the button for engaging the safety lock.
Item 4: the switch for turning the tool on and off.
Item 5 in the parts list: the shrub trimming blade.
Item 6: the guard for the grass cutter blade.
Item 7: the guard for the shrub trimming blade.
Item 8: the battery charger unit.
Carefully remove items from the box and inspect for damage or missing parts.
Do not operate if parts are damaged or missing; contact customer service.
Connect charger to tool and wall outlet. Red LED indicates charging status.
Handle may warm up; disconnect charger when not in use; do not use while charging.
Charge battery only between 0°-37.8°C (32°-100°F).
Allow battery to cool down after prolonged use before recharging.
Instructions on how to start and stop the tool using safety lock and trigger.
Tool is for light trimming of shrubs, hedges, and lawn edges, not commercial use.
Use for lawn edges and grass. Not for hedges or chopping. Avoid dirt and gravel.
Use for trimming and shaping shrubs and hedges. Not for grass or edging.
Check shrubs for objects, maintain secure footing, move steadily, and install guard after use.
Provides recommended times for cutting hedges and shrubs throughout the year.
Caution: Wear gloves when changing blades. Do not press safety lock button.
Press blade release button and slide blade downward to remove.
Align tab into slot, gear pin with oval slot, and push cover plate until it snaps.
Align tab into slot, gear pin with oval slot, and push cover plate until it snaps.
Caution: Do not press safety lock during maintenance. Check for defects.
If tool malfunctions, have it repaired by a qualified individual using identical parts.
Caution: Never clean shears in water to avoid injury and damage.
Keep blades sharp and clean. Lubricate with light machine oil before/after use.
Check blade edges for notches or burrs and remove them immediately.
Clean exterior with a soft brush and cloth. Do not use water or solvents.
Remove all debris from the tool after use.
Cover blades with the provided guards after use.
Charge battery 3-5 hours before storing. Recharge every 3 months for long-term storage.
Store tool in a dry, secure place out of reach of children.
Do not store in temperatures over 40°C (104°F) or in direct sunlight.
Do not store the tool in places with static electricity.
Call 1-800-633-1501 or visit americanlawnmower.com for support.
Record model and serial numbers for service and parts orders.
Identifies grass shear blade kit, shrub shear blade kit, and charger as repair parts.
Call 1-800-633-1501 for questions about operating or maintaining the shear.
Two-year limited warranty on equipment and battery packs/chargers.
Covers defects in materials and workmanship; repair or replacement of defective parts.
Excludes commercial use, abuse, negligence, and failure to follow manual instructions.
Excludes wear items, battery wear, damage from environmental extremes, and cosmetic wear.
Warranty is non-transferable and applies only to products sold by authorized retailers.
Excludes incidental, indirect, or consequential loss or damage from defects.
Original dated sales receipt must accompany all warranty claims.
The Yardworks 3.6V Lithium-ion Shrub Shear (Model LSS10163-1, SKU# 267-3168) is a versatile outdoor power tool designed for light trimming of shrubs, hedges, and lawn edges in private gardens and hobby areas. It is not intended for commercial, trade, or industrial use.
This cordless shear features a tool-less blade changing system, allowing users to easily switch between a 3.2-inch (80mm) grass cutter blade and a 6.3-inch (160mm) shrub trimming blade. The grass cutter blade is ideal for maintaining lawn edges and small grass areas, while the shrub trimming blade is used for shaping individual bushes, shrubs, and climbing plants. The device operates on a 3.6V lithium-ion battery, providing cordless convenience.
The product comes with a two-year limited warranty on the outdoor power equipment and a one-year limited warranty on battery packs and chargers. The warranty covers defects in materials and workmanship. It is voided if used for commercial/industrial purposes or due to operator abuse, negligence, or failure to follow instructions. Wear items (e.g., cutting blades, drive belts) and battery wear are not covered. The warranty is non-transferable and applies only to new products sold directly from an authorized retailer. Proof of purchase is required for all warranty claims.
General| Brand | Yardworks |
|---|---|
| Model | LSS10163-1 |
| Category | Power Tool |
| Language | English |
