CGO3 USER MANUAL
INTRODUCTION
CGO3 (available separately) is an innovave combinaon of 3-axis brushless
gimbal, camera and digital video downlink.
The Self-Stabilizing gimbal makes it possible to capture amazing photographs and
video footage for an array of uses. And the built-in digital video link delivers
streaming video to 5.8GHz WiFi compable iOS® and Android™ equipped devices
including smart-phones and tablets as well as YUNEEC Personal Ground Staons.
OPERATING INSTRUCTIONS:
(1) Insert the micro SD card into CGO3, plug in the power cord and slide the power switch, then
CGO3 start to work;
(2) When the green light starts to flash , it indicates that wifi has started to work. At this me, you
can take device to connect to CGO3's wifi, when the device is connected, the light will grow
solid green.
(3) Then press the shuer buon, CGO3 will take a picture; long press the shuer buon, CGO3
will enter recording funcon;
(4) Toggle the switch ,then CGO3 will be powered off.
OPERATION：
(1) Plug the 3-Pin power cord into the appropriate socket head.
(2) Install the gimbal under the belly of plane.
(3) Power on the plane, then gimbal will work.
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules.
These limits are designed to provide reasonable protecon against harmful interference in a resi-
denal installaon. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instrucons, may cause harmful interference to radio
communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is con-
nected.
This device complies with part 15 of the FCC rules. Operaon is subject to the following two condi-
ons:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tecon against harmful interference in a residenal installaon. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
ons, may cause harmful interference to radio communicaons. However, there is no guarantee
that interference will not occur in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
—Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modificaons not expressly approved by the party responsible for com-
pliance could void the user's authority to operate this equipment.
RF EXPOSURE WARNING
• This equipment must be installed and operated in accordance with provided instrucons and the
antenna(s) used for this transmier must be installed to provide a separaon distance of at least 20
cm from all persons and must not be co-located or operang in conjuncon with any other antenna
or transmier. End-users and installers must be provide with antenna installaon instrucons and
transmier operang condions for sasfying RF exposure compliance.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operaon is subject to the following two condions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired opera-
on of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitaon est autorisée aux deux condions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter tout brouillage radioélec-
trique subi, même si le brouillage est suscepble d'en compromere le fonconnement.
This equipment complies with IC RSS-102 radiaon exposure limit set forth for an uncontrolled
environment.
Cet équipement respecte les limites d'exposion aux rayonnements IC définies pour un environne-
ment non contrôlé
To Next Page
Need help?
General