This document is a user guide for a 2KW Electric Inset Fire from Zanussi, specifically for models ZEFIST1001SS and ZEFIST1003B. It provides essential information for safe operation, installation, usage, maintenance, and troubleshooting of the appliance.
Function Description
The Zanussi Electric Inset Fire is a heating appliance designed to provide warmth and a flame effect for domestic use. It operates as an electric local space heater with adjustable heat settings and a decorative pebble effect fire bed. The appliance can be controlled manually via buttons on the unit or remotely using the supplied remote control. It features automatic heating capabilities, a programmable timer, and adjustable flame brightness.
Important Technical Specifications
- Power Output: 2KW (2000W)
- Voltage: 220 - 240V AC; 50Hz
- Heat Settings: Low heat (1000W), High heat (2000W)
- Minimum Heat Output (indicative): 0.95 kW
- Nominal Heat Output: 1.9 kW
- Maximum Continuous Heat Output: 1.9 kW
- Auxiliary Electricity Consumption:
- At nominal heat output: 0.014 kW
- At minimum heat output: 0.014 kW
- In standby mode: 0.48 W
- Installation Dimensions (Minimum Opening):
- Width: 39 cm (15 1/2")
- Height: 55.5 cm (21 3/4")
- Depth: 11 cm (4 1/4")
- Mains Cable Length: Approximately 1.7 meters
- Fuse Requirement: 13 Amp fuse
- Heating Temperature Range: 15°C to 30°C
- Timer Settings: 10 programmable timer settings, each with its own date, power-on time, and shutdown time. Maximum duration for each setting is 23 hours 50 minutes.
- Flame Effect: LED light bulbs are used to create the flame effect, with five positions for brightness adjustment.
Usage Features
- Control Options: The appliance can be operated using either the control panel located under the pitched canopy or the supplied remote control.
- Manual Operation:
- On/Off: Press the On/Off button on the left of the control panel to turn the appliance on. A beep indicates power is on.
- Fire Effect: Press the I/O button on the right of the control panel to turn on the appliance and fire effect. A red light indicates it's on.
- Dimmer Mode: Press and hold the I/O button for 3 seconds to activate dimmer mode and adjust flame brightness.
- Heat Settings: Press the 1000W button once for low heat, twice to switch off. Press the 2000W button once for high heat, twice to switch off.
- Remote Operation:
- Power On/Off: Press the "ON/OFF" key on the remote.
- Heat Settings: Use 1000W or 2000W buttons for respective heat settings; press twice to switch off.
- Flame Dimmer: Use the DIMMER button to adjust flame effect brightness.
- Automatic Heating: Press the "IC" button to start or exit automatic heating, where the fireplace adjusts heating based on set and room temperatures.
- Date and Time Setting: Use "DATE TIME" button with "+" or "-" to set the day, hour, and minute, then "OK" to complete.
- Temperature Setting: Use "+" or "-" to set the desired temperature (15°C to 30°C). The set temperature must be higher than the room temperature for heating to work.
- Timer Setting: Press "TIMER SET" to enter timer mode. Use "+" or "-" to select power-on time, then "▲" to select shutdown time. "C" cancels the setting. The timer allows for setting specific days and times for the appliance to turn on and off.
- Safety Features:
- Overheat Protection: Automatically cuts off power to heating elements if temperature exceeds a limit. The heater will stop operating and requires cooling down.
- Safety Cut-off: Operates if the heater overheats (e.g., due to blocked air vents). It does not reset automatically. To reset, disconnect from mains for at least 15 minutes, then reconnect.
- Control Options (Information Requirements for Electric Local Space Heaters):
- Electronic room temperature control plus week timer: [yes]
- With adaptive start control: [yes]
Maintenance Features
- Cleaning:
- Always disconnect from the mains and allow the appliance to cool completely before cleaning.
- Do not immerse the cord, plug, or appliance in liquid.
- Clean the outer surface with a moist cloth, then wipe with a dry, soft cloth.
- Avoid harsh detergents, abrasives, or spray cleaners.
- Ensure no water seeps into openings or contacts electrical connections.
- Allow sufficient drying time before re-operating.
- Regularly clean air inlets and outlets with a vacuum cleaner using a brush attachment (at least twice a year with regular use).
- Storage: When not in use, re-pack the heater in its original packaging and store it in a cool, dry place.
- Fuse Replacement: Instructions are provided for changing the 13 amp fuse in the plug using a screwdriver.
- Professional Servicing: The appliance uses LED light bulbs for the flame effect and should only be serviced by qualified electricians. In case of malfunctions or physical damage, do not attempt to repair it yourself; consult qualified personnel.
Important Safety Instructions
- Read all instructions before use.
- Ensure mains voltage matches appliance rating.
- Do not leave unattended when connected to mains.
- Position upright on the floor, away from curtains, furniture, or flammable items.
- Do not touch hot surfaces.
- Do not immerse in water or operate with wet hands.
- Do not let the cord hang over edges or touch hot surfaces.
- Do not operate with a damaged cord or plug; if damaged, the appliance should be scrapped.
- Do not use accessory attachments not recommended by the manufacturer.
- Do not remove parts from the appliance.
- Do not use near baths, showers, or swimming pools.
- Do not use on or near hot surfaces.
- Do not move by pulling the cord.
- Do not place flammable objects or clothing on top of the appliance.
- Turn off before moving the heater.
- Allow at least 15cm safe area around the appliance for air circulation.
- Keep air inlets and outlets clean to prevent overheating; DO NOT COVER.
- Do not use in rooms with explosive gas or flammable glues/sprays/solvents.
- Do not use with an extension lead.
- Do not place any body part near air inlet/outlet/fins.
- Built-in overheating safety device will shut off the appliance if overheating occurs.
- Do not insert foreign objects into the grill.
- Keep grills clear of draped fabric or curtains.
- Do not locate immediately below a mains socket.
- Do not use with a programmer, timer, or any other device that switches the appliance on automatically, as this poses a fire risk if covered or positioned incorrectly.
- Intended for household heating use only, not commercial or outdoors.
- Children aged 8 years and above, and persons with reduced capabilities, can use the appliance with supervision and instruction. Children shall not play with the appliance or perform cleaning/maintenance without supervision.
- Children under 3 years should be kept away unless continuously supervised. Children aged 3-8 years shall only switch on/off if installed in its normal operating position and with supervision/instruction; they shall not plug in, regulate, clean, or perform user maintenance.
- This appliance must be plugged into an earthed socket.
Need help?
General
To Next Page