Why won't my Zanussi Washer start?
If your Zanussi Washer doesn't start, ensure the mains plug is correctly connected, the door is closed, and there are no blown fuses. Also, confirm you've pressed the Start/Pause button. If a delay start is active, either cancel it or wait for the countdown. Finally, deactivate the Child Lock if it's enabled and check that the knob is in the correct position for your selected program.
What to do if my Zanussi ZW84PCBI Washer is not draining?
If your Zanussi Washer isn't draining water, check that the sink spigot isn't clogged and that the drain hose has no kinks or bends. Also, make sure the drain filter isn't clogged by cleaning it, if necessary. Verify the drain hose connection is correct. Finally, if you selected a program or option that ends with water in the tub, set the drain program.
Why is the spin cycle on my Zanussi ZW84PCBI Washer not working?
If your Zanussi Washer's spin phase isn't working or the cycle is longer than usual, first set the spin program. Check and clean the drain filter if it's clogged. If the issue is due to balance problems, manually adjust the items in the tub and restart the spin phase.
What to do if you cannot open the Zanussi ZW84PCBI door?
If you can't open the door of your Zanussi Washer, ensure a program that ends with water in the tub hasn't been selected and that the washing program is finished. If there's water in the drum, set the drain or spin program. Confirm the appliance has electrical power. If these steps don't work, this problem may be caused by a failure of the appliance. If you need to open the door, please read carefully 'Emergency door opening'.
What to do if there is water on the floor near my Zanussi ZW84PCBI?
If there's water on the floor near your Zanussi Washer, ensure the water hose couplings are tight and not leaking. Check the water inlet and drain hoses for damage. Also, make sure you're using the correct detergent in the proper amount.
How to improve washing results with Zanussi ZW84PCBI Washer?
If your washing results from the Zanussi Washer are not satisfactory, increase the detergent quantity or switch to a different detergent. For stubborn stains, pretreat them with special stain removal products before washing. Ensure you're setting the correct temperature and avoid overloading the machine.
How to fix Zanussi ZW84PCBI Washer not filling with water?
If your Zanussi Washer isn't filling with water properly, start by checking that the water tap is fully open. Make sure the water supply pressure isn't too low. Ensure the water tap isn't clogged and the inlet hose has no kinks, damages, or bends. Verify the water inlet hose connection is correct. Lastly, check that the filter of the inlet hose and the filter of the valve aren't clogged.
Why is my Zanussi Washer making unusual noises and vibrating?
If your Zanussi Washer is making unusual noises and vibrating, ensure it's correctly leveled. Also, check that all packaging and transit bolts have been removed. If the load is too small, add more laundry to the drum.
How to reduce too much foam in Zanussi ZW84PCBI Washer?
If there's too much foam in the drum of your Zanussi Washer during the washing cycle, try reducing the amount of detergent you're using.
Why does Zanussi ZW84PCBI programme duration increase or decrease?
If the programme duration of your Zanussi Washer increases or decreases during execution, it's because the AutoAjust System adjusts the duration based on the laundry type and load size.
General| Load type | Front Load |
|---|---|
| Capacity | 8 kg |
| Spin speed | 1400 rpm |
| Category | Washer |
| Maximum spin speed (rpm) | 1400 RPM |
| Washing capacity (kg) | 8 kg |
| Dimensions (H x W x D) | 85 x 60 x 59 cm |
To Next Page
