What to do if the door latch cannot be remotely opened by the Zartek CDP-801 Intercom System handset?
If the door latch cannot be remotely opened by the Zartek Intercom System handset, it might be due to a few reasons. First, ensure that the door lock opening button 13 is activated. Also, verify that there is a DC supply to the Caller unit. Finally, check the connections at the terminal block to ensure they are properly connected.
Why Zartek CDP-801 Intercom System handset and caller unit cannot communicate?
If the Zartek Intercom System handset and caller unit cannot communicate, the issue might stem from a few causes. It could be that the handset and caller unit have different ID codes, in which case you should perform the pairing process. Alternatively, the battery in the caller unit might have run down, requiring a replacement. Another possibility is that the handset battery needs recharging using the charger stand.
How to improve communication distance on Zartek Intercom System?
If the communication distance of your Zartek Intercom System has become short, consider these possible causes: * Many steel structures may be present between the handset and caller unit. Try relocating the position of the handset. * The battery in the caller unit may have run down. Replace it with a new battery. * The handset battery may need recharging. Use the charger stand to recharge it.
Why can't I perform intercom between handsets on my Zartek Intercom System?
If you cannot perform intercom between handsets on your Zartek Intercom System, it could be due to the following reasons: * The units are not properly paired. Perform the pairing process. * The battery has run down. Recharge the battery using the charger stand.
What to do if Zartek CDP-801 handset or gatestation has no power or is frozen?
If the Zartek Intercom System handset or gatestation has no power or is frozen, consider the following: * The battery may be faulty or flat. Replace the battery. * The software may be confused. Reset the unit by removing all power and then reconnecting it.
Why new Zartek CDP-801 Intercom System caller unit (backgate) cannot communicate with indoor unit?
If a new caller unit (backgate) cannot communicate with the indoor unit of your Zartek Intercom System, it is likely that the new unit is not properly paired to the existing units. To resolve this, perform the pairing process.
Why is the out-of-range alert always on for my Zartek CDP-801?
If the out-of-range alert is always on for your Zartek Intercom System, it indicates that there may be no power supply to the caller unit. Replace the battery or check the DC supply to the caller unit.
What does it mean if the self battery low icon is always on for Zartek CDP-801 Intercom System?
If the self battery low icon is always on for your Zartek Intercom System, the battery pack is likely damaged and cannot be recharged. Replace it with a new battery pack.
General| Model | CDP-801 |
|---|---|
| Type | Intercom System |
| Power Supply | DC 12V |
| Operating Temperature | -10°C to +50°C |
| Humidity | 10% ~ 90% |
Connects the DC supply to the caller unit for operation and illumination.
Instructions for charging the handset's Li polymer battery pack via the charger stand.
Steps to match the caller unit with handsets for secure, interference-free communication.
Guide to selecting a suitable location and securely installing the caller unit.
Wiring instructions for connecting the gatestation to a gate motor using a relay.
Instructions for wiring a striker lock, requiring a separate relay and power supply.
Identification and function of buttons and indicators on the caller unit.
Overview of handset buttons, display elements, and charging contacts.
Explanation of various icons displayed on the handset LCD screen.
Turning on/off, battery status, and adjusting incoming call alert methods.
Initiating calls from the caller unit and answering calls on the handset.
How to use the intercom feature between multiple handsets within an apartment.
Guidance for resolving communication, range, and door lock issues.
Information on fitting an optional external antenna for improved reception.
A template for drilling holes for mounting the caller unit on different wall types.
To Next Page