Zenit blueBOX User Manual (English)

Other manuals for Zenit blueBOX

Questions and Answers:

J
james16Aug 18, 2025
Why is my Zenit Plumbing Product system noisy and vibrating?
- A
  Allison JonesAug 18, 2025
  The noise and vibration in your Zenit Plumbing Product system could be due to a few reasons: either the pipelines are not secured to the walls, the pump is unbalanced by a foreign body, or the pump is operating with cavitation. To resolve this, secure the pipelines to the walls using vibration damping mounts. Also, check the pump to ensure it is not blocked by any solids and is operating within its characteristic curve.
J
James PattersonAug 20, 2025
What to do if my Zenit Plumbing Product pump is running but no water is being pumped?
- P
  Pedro JonesAug 20, 2025
  If your Zenit Plumbing Product pump is running but not pumping water, it might not be primed. Prime the pump by lifting it and then putting it back in place, ensuring you fill the pump body with liquid.
A
Ashley MerrittAug 23, 2025
Why does the level in the toilet drop when the Zenit Plumbing Product pumps are in operation?
- S
  Stephanie SmithAug 23, 2025
  The level in the toilet drops when the Zenit Plumbing Product pumps are running because the vent pipe is either not fitted or insufficient. Install a vent pipe or check the existing one.
J
johnmorganAug 26, 2025
Why do air bubbles rise up in the toilet after I flush my Zenit Plumbing Product?
- J
  Jennifer TrujilloAug 26, 2025
  If air bubbles rise up in the toilet after flushing your Zenit Plumbing Product, it's likely due to a vent pipe not being fitted or being insufficient. Install a vent pipe, or inspect the existing one to ensure it's adequate.
W
wharperAug 28, 2025
What to do if there are leaks at the pipe entrance/exit points of my Zenit Plumbing Product?
- D
  Denise WrightAug 28, 2025
  If you notice leaks at the pipe entrance or exit points of your Zenit Plumbing Product, it's probably because the gaskets are not fitted correctly. Locate the leak, check the seal to ensure it is correctly fitted, and replace it if necessary.
J
jason94Aug 30, 2025
What to do if the tank shifts or sinks after installing my Zenit Plumbing Product in the ground?
- K
  Kim ParkerAug 30, 2025
  If the Zenit Plumbing Product tank shifts or sinks after being installed in the ground, it is likely because there is no plinth underneath the tank or the ground isn't firm enough. Remove the tank and install it correctly, ensuring a solid foundation.
G
Gerald MartinezSep 1, 2025
How to prevent the tank of my Zenit Plumbing Product from sagging when liquid enters it?
- K
  Kevin MasonSep 1, 2025
  The tank of your Zenit Plumbing Product sags when liquid enters it because the incoming liquid is too hot. Lower the temperature of the liquid by mixing it with cold water.
K
kennethlawrenceSep 3, 2025
Why is my Zenit Lifting Systems so noisy and vibrating?
- M
  Mikayla RichardsonSep 3, 2025
  If your Zenit Lifting System is noisy and vibrating, it could be due to a couple of reasons. First, the pipes might not be properly secured to the walls, or the pump could be unbalanced by a foreign object. To address this, secure the pipes to the walls using anti-vibration joints and inspect the pump to ensure it's free from any solid matter. Another possibility is that the pump is operating in cavitation conditions. In this case, verify that the pump is operating within its characteristic curve.
M
Michael CollinsSep 6, 2025
How to fix leaks at the inlet/outlet pipes of Zenit Lifting Systems?
- A
  Angela DavisSep 6, 2025
  If you notice leaks at the inlet or outlet of the pipes in your Zenit Lifting Systems, it's likely due to incorrect installation of the gasket. To resolve this, locate the leak, inspect the gasket installation, and replace the gasket if necessary.
J
Jessica HutchinsonSep 8, 2025
What to do if buried Zenit blueBOX tank sinks or moves?
- Y
  ytorresSep 8, 2025
  If, after burying your Zenit Lifting Systems tank, it sinks or moves, it's likely because there's no slab beneath the tank or the ground isn't firm enough. To fix this, remove the tank and restore the correct installation conditions, ensuring a solid base.

Zenit blueBOX Specifications

General

Brand	Zenit
Model	blueBOX
Category	Lifting Systems
Language	English

Zenit blueBOX Use And Maintenance Instructions

Table of Contents

Other manuals for Zenit blueBOX

Questions and Answers:

Zenit blueBOX Specifications