ZIMO MX648 - Special Effects for Function Outputs

Non-Sound Decoder MX600 - MX638 and Sound Decoder MX640 - MX659 Page 33
 The effect-CV’s are also suitable for
direction dependent function outputs
without using a special effect (with effect code 000000).
EXAMPLE:
CV #127 = 1, CV #128 = 2, CV #35 = 12 (FO1, FO2 operate directional, ON/OFF with F1 key).
CV
Denomination
Range
Default
Description
#125
1
Special effects
According to list above
for
function output F0 (front
headlight)
Effects can be further
adjusted and modified
with
CV’s #62 - 64
and
CV #115, #116
(for uncoupler).
0
Bits 1, 0 = 00: bidirectional (active in both directions)
= 01: only active in forward direction
= 10: only active in reverse direction
ATTENTION in case of CV #125 and #126: change
CV’s #33, 34.... if direction is wrong!
Bits 7, 6, 5, 4, 3, 2 = Effect-Code
EXAMPLES
You want : Program CV #125 to:
Mars light forward only - 00000101 = 5
Gyralite independent of direction - 00011100 = 28
Ditch type 1 left, only forward - 00100101 = 37
Uncoupler - 00110000 = 48
Soft start of output - 00110100 = 52
Automatic stop light - 00111000 = 56
Automatic cab light OFF - 00111100 = 60
Speed/load depen. smoke - 01001000 = 72
Speed/load depen. diesel smoke - 01010000 = 80
#126
Special effects
for
rear headlight
(default F0 reverse)
0
As in CV #125, only for rear headlights
#125  Front headlight
#126  Rear headlight
#127 -
#132
Special effects for
FO1, FO2, FO3,
FO4, FO5, FO6
FO3 and up NOT for MX621
0
See CV #125 for details
#127  FO1 #128  FO2
#129  FO3 #130  FO4
#131  FO5 #132  FO6
#159,
#160
Special effects for
FO7, FO8
0
See CV #125 for details
#159  FO7 #160  FO8
ATTENTION: “Coupler” and “Smoke” effects could be
used with FO0 - FO6 have now moved to FO7 - FO8
with SW version 34 or higher.
#62
Effects modifications
0 - 9
0
Change of minimum dimming value
#63
Light effects
modifications
or
Stop light OFF delay
0 - 99
0 - 255
51
Tens digit: sets cycle time (0 - 9, default 5), or start-up
time during “soft start” with 001101 (0 - 0,9s)
Ones digit: extends OFF time
For stop light OFF delay (001110xx in CV #125, 126
or 127): Time in tenths of a second the stop lights re-
1
Note to ditch lights: Ditch lights are only active when headlights and function F2 (#3 on Zimo cab) are on, which is prototypical for North American railroads. The
ditch lights will only be working if the applicable bits in CV #33 and 34 are on (the definition in CV #125 - 128 in itself is not enough but a necessary addition).
Example: If ditch lights are defined for FO1 and FO2, the bits 2 and 3 in CV #33 and 34 have to be set accordingly (i.e. CV # 33 = 13 (00001101), CV #34 = 14
(00001110).
main ON after the tram comes to a full stop (range: 0 –
25 sec.).
#64
Effects modifications
0 - 255
0
Bit 7 - 4: define a ditch light-key (function key+1)*16
consequent: 0=F2, 1=F0, 2=F1,.. 15=F14
Bit 3 - 0: Ditch light OFF time modification [s]Ditch light
off time modification
#393
ZIMO-Config. 5
0 – 255
0
Bit 0 = 1: activate ditch light if bell is played
Bit 1 = 1: activate ditch light if horn is played
#190
Fade-in time for
88, 89, 90 effect
from SW version 33.10
(regarding Value 0 from SW
version 34)
0 - 255
0
= 0: 0,5 sec.
= 1: 1 sec fade-in time
= (i.e.) 5: @ 4 sec
= 255: @ 320 sec
ATTENTION: Above values are valid for a “cycle time”
5 (i.e. CV #63 = 50 … 59). About 1/6 of the time with
cycle time 0; double time with cycle time 9.
#191
Fade-out time for
88, 89, 90 effect
from SW version 33.10
(regarding Value 0 from SW
version 34)
0 - 255
0
= 0: invalid value for SW version 33; later 0,5 sec.
= 1: 1 sec fade-out time
= (i.e.) 5: @ 4 sec
= 255: @ 320 sec
ATTENTION: Above values are valid for a “cycle time”
5 (i.e. CV #63 = 50 … 59). About 1/6 of the time with
cycle time 0; double time with cycle time 9.
#353
Automatic
smoke generator
shut-down
0 - 255
=
0 - 106 min
0
For special effect codes “010010xx” or “010100xx”
(smoke generator): Overheat protection: turns OFF af-
ter ½ min to about 2 hours.
= 0: Won’t turn off automatically.
= 1 … 255: Switches off autom. after 25 seconds/unit.
3.23 Configuration of Smoke Generators (for sound decoders)
Smoke generator without fan (Example: Seuthe 18V):
In addition to a simple ON/OFF function via a function output of your choice, the smoke intensity can
also be programmed to change between standstill, or cruising and acceleration.
This requires the smoke generator to be connected to one of the function outputs FO1…FO8 (FO7
and FO8 only with SW version 34 or higher) and the selected output must be programmed for the de-
sired effect with the associated “effect CV” (with CV #127 for FO1, CV #128 for FO2 etc.); in this case
for load dependent smoke of steam engines (effect code “72”) or load dependent smoke of diesels
(effect code “80”).
The smoke generator characteristic as defined by CV #137, 138 and 139 is used for the relevant
function output. These CV’s must be programmed (with appropriate values) otherwise the smoke
generator will not produce any smoke.
EXAMPLE: - Typical characteristic for a track voltage set around 20V with above smoke generator:
CV #137 = 70…90: little smoke at standstill.
CV #138 = 200: The smoke intensity is increased to about 80% of its maximum capacity beginning
with speed step 1 (at very low speed), which produces relatively heavy smoke.