What to do if the Zodiac Ultrasonic Jewelry Cleaner control box does not respond?
If your Zodiac Ultrasonic Jewelry Cleaner control box isn't responding, try unplugging the power cord from the mains socket, waiting 10 seconds, and then plugging it back in.
How to fix if part of the pool is not correctly cleaned by Zodiac Ultrasonic Jewelry Cleaner?
To address this issue with your Zodiac Ultrasonic Jewelry Cleaner, repeat the immersion steps, and try different locations in the pool until you find the right spot.
Why Zodiac Ultrasonic Jewelry Cleaner does not climb pool sides?
If your Zodiac Ultrasonic Jewelry Cleaner isn't climbing the pool sides as well as it used to, it could be due to several reasons. The filter might be full or clogged, so try cleaning it with fresh water. If it's severely blocked, use an acid solution like spirit vinegar. Replace the filter if necessary. Also, check if the tires are worn and replace them if needed. Microscopic algae may be present, requiring shock chlorination and a slight reduction in pH, but remove the appliance during shock treatment. Finally, inspect the brushes for wear and replace them if necessary.
How to stop Zodiac Ultrasonic Jewelry Cleaner cable from tangling?
To prevent the Zodiac Ultrasonic Jewelry Cleaner cable from tangling, avoid unrolling the entire length of the cable into the pool. Place only the necessary length in the pool and spread the rest along the side.
Why Zodiac Ultrasonic Jewelry Cleaner does not stay on pool bottom?
If your Zodiac Ultrasonic Jewelry Cleaner isn't staying firmly on the pool bottom, it might be due to air trapped inside. Repeat the immersion steps to remove any air. Another reason could be a full or clogged filter; clean it with fresh water or an acid solution like spirit vinegar, and replace it if needed. Also, inspect the propeller for damage.
What to do if Zodiac Ultrasonic Jewelry Cleaner does not move?
If your Zodiac Ultrasonic Jewelry Cleaner isn't moving upon start-up, first ensure the control box's power socket is receiving power. Also, verify that a cleaning cycle has been initiated and that the lights are on.
General| Brand | Zodiac |
|---|---|
| Model | Vortex OV 3400 |
| Category | Swimming Pool Vacuum |
| Language | English |
Explains debris suspension via patented cyclonic suction and motor tilt.
Details the 3 motors (2 traction, 1 suction pump) and the tilt sensor.
Features the extra-wide 27 cm suction inlet for efficient debris pickup.
Describes front and rear driving wheels, including 4WD, for improved maneuverability.
Highlights easy filter access, large 5L capacity, and available filtration levels.
Discusses standard blue plate and reinforced Contact+ brushes for cleaning.
Covers standard and sucker tyres, their suitability for different pool surfaces.
Details the trolley's benefits for use, transport, storage, and assembly.
Explains the swivel feature to prevent cable tangling during operation.
Describes the protective cover for weather protection and storage.
Covers timer, out-of-water safety, and motor protection for autonomy, reliability, and performance.
Lists all components included in the product packaging.
Explains the meaning of various symbols used on the device and control interface.
Provides detailed specifications for different models, including dimensions and power.
Identifies and labels all external parts of the cleaner for user reference.
Advises on the minimum distance for the command unit placement relative to the pool edge.
Provides step-by-step instructions for assembling the cleaner's carriage without tools.
Details how to attach the cleaner's command unit to its base for protection.
Explains the cleaner's adaptability to various pool types, shapes, and bottoms.
Matches pool dimensions with the appropriate floating cable length.
Outlines available cleaning modes: surface, shape, and intensity settings.
Lists recommended pool water conditions for optimal cleaner performance.
Illustrates the correct procedure for immersing the cleaner to prevent cable tangling.
Guides on safe electrical connection, ensuring proper sealing against splashing.
Explains how to start and change cleaning cycles with default options.
Details the "Lift System" for easy cleaner removal from water, reducing effort.
Covers remote control operation, including removal mode and robot control.
Instructions for setting the time and programming multiple cleaning cycles.
Explains how to adjust the cleaning duration by +/- 0.5 hours.
Steps for cleaning or replacing the filter, including replacement intervals.
Instructions for cleaning the propeller and checking for obstructions.
Guidance on replacing brushes, noting wear indicators and replacement frequency.
Steps for replacing the cleaner's tyres, with advice for tiled pools.
Guides users on interpreting LED flashing and error codes for basic troubleshooting.
Details technical procedures and diagnostic menus reserved for professional users.
Explains how to access the user diagnostic menu for operating time and error history.
Details access to the PRO after-sales menu for fault codes and error history.
Details the Quick Test and Full Test options via the Diag Box for diagnostics.
Troubleshooting steps for issues with climbing pool walls, focusing on filter and brushes.
Addresses filtration problems and poor adhesion, suggesting checks and filter changes.
Solutions for stability issues, including air removal, filter check, and propeller condition.
Focuses on filter clogging and the importance of regular filter cleaning.
Explains how to diagnose and fix problems with the remote control's range.
Lists various technical procedures for dismantling, reassembly, and component replacement.
To Next Page