2gig Technologies PASSIVE INFRARED MOTION DETECTOR User Manual (English)

To Next Page

PASSIVE INFRARED MOTION DETECTOR

FCC ID: WDQ-PIR1345

Industry Canada ID: 7794A-PIR1345

INSTALL INSTRUCTIONS

ThePassiveInfraredMotionDetectorisawall‐mountedunitwithwide

anglemotionprotection.WhensettoHighSensitivityMode,thePassive

InfraredMotionDetector(PIR)hasamaximumrangeof30feetdeepx50

feetwide. ThePIRispetimmuneupto55lbs.

Box Contents

•Detector

•3VLithiumbattery

•3screwsand2dowels

•Bracket

•Flatwallmount

•Cornermount

Programming

Thefollowingstepsdescribegeneralguidelinesforprogramming

(learning)thePIRint otheControlPanel.Scrollbetweenoptionsusingthe

←and→arrows.Movetothepreviousornextpromptbypressingthe↑

and↓arrows.

1 SelectRFsensor#(01to48).AssignthePIRtoanewzone.

2 SelectRFsensortype:

(04)interiorfollower

(10)int

eriorwithdelay

3 SelectRFsensorequipmentcode.Enter0533forthePassiveInfrared

MotionDetector.

4 SelectRFequipmenttype.

(2)moti

5 EnterRFsensorserialnumber(7digits).

ManualEntry:Typeinthelast7digitsoftheTXIDthatisfound

outsideoftheboxoronthebackofthedevice.

AutoEntry:WiththepanelinLearn‐inmode,(pressShiftthenLearn)

pressthetamperswitch.ThecorrectTXIDshouldap

pear.Acceptthe

correctTXIDbypressingok.

Remembertopr

essthe↓arrowtocontinuegoingthroughthe

systemconfigurationprompts.

6 SelectRFsensorequipmentage(0to1).

(0)new(

productisnew)

(1)ex

isting(productalreadyexists)

7 SelectRFsensorloopnumber(1to3).

8 SelectRFSensordialerdelay(0to1)

(0)disable

(1)ena

bled

9 ConstructRFsensorvoicedescriptor.PressInsertthenpressany

numberbetween002and255toaddaword.Repeatthisforeach

word.Forexample,ifyouwanttonamethisPIRasthe“master

bedroom,”pressInsertthenpress140formaster.PressInsertthen

press024forbedroom.

10 SelectRFsensorreports(0to1).

(0)disable

d(PIRdoesnotreporttothecentralstation)

(1)ena

bled(PIRreportstothecentralstation)

11 SelectRFsensorsupervised(0to1)

(0)disable

d(detectordoesnotreportlossofsupervision/lowbattery)

(1)ena

bled(detectorreportslossofsupervision/lowbattery)

12 SelectRFsensorchime(0to13).

(0)disable

d(panelwillNOTchimewhenPIRisactivated)

(1‐13

)enabled(selectsavoiceandchimetosoundonthepanelwhen

thePIRisactivated)

13 Toprogramanothersensorclicknext.

14 Toexitprogramming,clickskipthenendandexit.Uponexit,the

paneltakesaseveralsecondstoreboot.

Testing

Beforemountingthedetector,ensurethatthePIRmountinglocation

providesgoodRFcommunicationtothepanel.Toverify,dothefollowing:

1 FromtheInstallerToolbox,selectwalktest.

2 PlacetheamagnetoverthearrowontheleftsideofthePIR,(the

detector’sLEDindicatesthatamagnethasbeendetected)andthen

removethemagnet(amagnetisnotsupplied).

3 PlacethePIRinthelocationthatyouplanonmountingit.

4 MoveintheareathatistobecoveredbythePIRandmakesurethat

theLEDonthePIRflasheseverytimeyoumove.TheLEDflashing

continuesfor1minutesoyoucancheckthePIRbeamcoverage.

NOTE: Thereisa3‐seconddelaybetweenflashesontheLED.

IMPORTANT: Thefollowingcancauseafalsealarmwhentesting:

•Leavingthecoveroff

•Removingjumpers

• PositioningthePIRindirectsunlightorcloseproximitytoaheatingor

anairconditioningduct

5 Exitinstallertoolbox.

Inserting and Replacing Batteries

IfasupervisedPIRbatteryislow,alowbatterynotificationisindicatedon

theControlPanel’ stouchscreen.Ifindicated,replacethebattery

immediately.Useonlytherecommendedreplacementbatteries(See

Specifications).

•Removebackcoverbyunscrewingbottomscrewandpullbackcover

frombottomtotop.Observethepolarityofthebat

tery.SeeFigure2.

WARNING: Improperhandlingoflithiumbatteriesmayresultinheat

generation,explosionorfire,resultinginpersonalinjuries.

Replaceonlywiththesameorequivalenttypeofbatteryas

recommendedbythemanufacturer(seeSpecifications).

Batteriesmustnotberecharged,disassembledordisposedofinfire.

Disposalofusedbatteriesmustbemadeinac

cordancewiththe

wasterecoveryandrecyclingregulationsinyourarea.KeepAway

FromSmallChildren.Ifbatteriesareswallowed,promptlyseek

medicalattention.

CaliforniaOnly:ThisPerchloratewarningappliesonlytoManganese

DioxideLithiumcellssoldordistributedONLYin/California,U.S.A.

PerchlorateMaterial‐specialhandlingmayapply.Seedt

sc.ca.gov/

hazardouswaste/perchlorate.

Installing and Mounting

RemovethescrewfromthebottomofthecaseandopenthePIR(see

Figure1).

1 Installthe3VLithiumbatteryfromthebox.

2 Settheleftjumper(PETIMMUNITY)toeither33lbs.(15kg)or55lbs.

(25kg;default).(seeFigure2)

3 Settherightjumper(SENSITIVITY)toeitherLO(default)orHI(see

Figure2).

4 Pressandreleasethetamperswitchtobeginthepowerupprocess.

5 Wait10secondsforthePIRtofullypowerup.

Need help?

Do you have a question about the 2gig Technologies PASSIVE INFRARED MOTION DETECTOR and is the answer not in the manual?

2gig Technologies PASSIVE INFRARED MOTION DETECTOR Specifications

General

Type	Passive Infrared Motion Detector
Supervisory Signal Interval	60 minutes
RF Frequency	345 MHz
Detection Method	Passive Infrared
Field of View	90°
Operating Temperature	32°F to 120°F (0°C to 49°C)
Power Source	3V Lithium Battery
Battery Life	Up to 5 years
Compatibility	2GIG Systems
Mounting	Wall