Why is there louder talk volume or feedback from my 3M C1060 headset?
If you are experiencing louder talk volume or feedback from a single 3M Intercom System headset, call for authorized service because the holes in the back of the microphone may be plugged with dirt or grease.
How to fix audio that cuts out on 3M Intercom System headsets?
If the audio on your 3M Intercom System headsets cuts out or is interrupted, it could be due to radio interference. Try changing the channel on the base station to one that is at least three channels away from the current one. If you are using a single base station, move jumper J3 to the lane 2 position to access 8 additional channels. Also, try to locate and turn off any other 900 MHz devices in the building, such as cordless phones, video and speaker systems, and video monitors. It may also be caused by a poor location of the Base Station. Try relocating the Base Station, or adding an additional Base Station to extend the range of the system.
What to do if a 3M C1060 headset is dead?
If a single 3M Intercom System headset is dead and producing no static, first ensure that the headset is turned on by pressing the ON button. If it still doesn't work, the battery may be discharged; replace it with a fully charged one. If the problem persists, the headset may be defective, and you should call for authorized service.
How to fix static on a single 3M C1060 Intercom System headset?
If a single 3M Intercom System headset hears static, first, reprogram the headset with the programming station to ensure it's on the same channel as the base station. If the issue persists, try programming other headsets. If they won’t program, replace the programming station. If other headsets program OK, the single headset may be defective and needs repair.
Why is there no talk or listen from the menu sign on my 3M C1060's backup wired intercom?
If you experience no talk or listen from the menu sign when using the backup wired intercom on your 3M Intercom System, but the C1060 system works OK, ensure that the base station is turned OFF. Also, check that the backup intercom has power by turning it on or plugging in its power transformer. Make sure the volume controls are turned up on the backup intercom. If problems persist, the backup intercom or its wiring may be defective, and you should call for authorized service.
Why is there no vehicle alert tone in my 3M Intercom System headset?
If the vehicle alert tone is not heard in the 3M Intercom System headset, ensure the vehicle detector is receiving power by plugging it into a power outlet or replacing the detector fuse. If the detector seems 'locked up', remove power to it for a few seconds to reset it. Also, check that the base station alert tone volume is not set too low and adjust it accordingly.
What to do if a single 3M C1060 headset is dead?
If a single 3M Intercom System headset is dead (no static), first ensure the headset is turned on by pressing the ON button. If it still doesn't work, the battery might be discharged; replace it with a fully charged one. If the problem persists, the headset itself may be defective, and you should call for authorized service.
Why doesn't the green light come on when charging my 3M Intercom System battery?
If the green light on the charger of your 3M Intercom System never illuminates, replace the battery, because it may be defective.
Why does my 3M Intercom System headset have constant programming tones?
If you are hearing constant programming tones on a single 3M Intercom System headset and the programming cable has no effect, the headset is likely defective, and you should call for authorized service.
How to extend battery life on a 3M Intercom System?
If you are experiencing short battery life with your 3M Intercom System, the batteries may be worn out and need replacement. Also, ensure that the correct type of power transformer is being used for the charger, specifically one marked 'Secondary Voltage 14 VAC.'
General| Brand | 3M |
|---|---|
| Model | C1060 |
| Category | Intercom System |
| Language | English |
To Next Page
