5 Apply one to two turns of PTFE tape (not included) to
threads of fittings. Thread fittings into ports of filter body.
Tighten fittings snuggly, but DO NOT over tighten.
6 Connect the inlet port of the filter to the incoming water
line following steps 7 & 8.
7 Insert end of tubing into compression fitting; hand tighten
nut onto threads of fittings.
8 With wrench or pliers, tighten compression nut one full turn.
CAUTION: DO NOT OVER TIGHTEN.
9 Turn on the incoming water sup-
ply to flush out the filter into a bucket
or pan thereby removing fine particles
of charcoal which may be present
in the filter body. Flush cartridge in
accordance with Performance Data
Sheet or Flush Instruction Card.
10 Connect the outlet port of the filter
to the water line going to your equip-
ment being served.
11 Turn on water supply line. If leak occurs, tighten nuts or
fittings until leak stops.
12 After six months, simply replace with another CFS717.
13 Use of the two (2) included plastic mounts is recom-
mended, particularly if your tubing is of a non-rigid material.
Proceed as follows:
a) Peel protective backing from mounting pads and firmly
apply to a clean surface. Mount pads 8 3/8” to 8 1/2” apart
in a direction that most readily accommodates your tub-
ing. Adhesive backing may prove inadequate on certain
surfaces. A wood screw or other suitable fastener may be
use by piercing through the center of the mounting pad.
CAUTION: Make certain fasteners do not contact hidden
electrical wiring.
b) Pass straps through eyelets of mounting pads with
the toothed surface of the straps facing you.
c) Position the CFS717 filter over mounting pads, loop
straps around bass fittings in filter body and fasten straps
securely. IMPORTANT: Straps cannot be unfastened
once closed—make certain filter is correctly mounted
before fastening.
d) When replacing filter, cut straps with snippers or
scissors. A new mounting kit is furnished with each re-
placement filter.
NOTE: Activated carbon filters are not intended for use where
water is microbiologically unsafe or of unknown quality.
CUNO Incorporated warrants this Product (excluding dispos-
able filter cartridge(s)) to be free from defects in material and
workmanship for five (5) years from the date of purchase.
The disposable filter cartridge is warranted from defects
in material and workmanship for a period of one (1) year
from the date of purchase. This warranty does not cover
failures resulting from abuse, misuse, alteration or damage
not caused by CUNO or failure to follow installation and use
instructions. If the Product is defective CUNO will replace the
Product or refund your Product purchase price. CUNO will
not be liable for any indirect, special, incidental, or conse-
quential damages arising from the use of this Product. Some
states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation may not
apply to you. To obtain warranty service, mail your request to
Warranty Claims, CUNO Incorporated, 400 Research Park-
way, Meriden, CT 06450. Proof of purchase (original sales
receipt) must accompany the warranty claim, along with a
complete description of the Product, model number and al-
leged defect. This warranty gives you specific legal rights
and you may have other rights which vary from state to state,
or country to country.
SPECIFICATIONS
Model Service Service Max. Max.
Flow Rate Life Press. Temp.
CFS717 0.5 gpm 1500 gal. 125 psi 100°F
(1.9 lpm) (5678 lit.) (8.62 Bar) (38°C)
INSTRCFS717 0909
© 2009 3M Company. All rights reserved.
CUNO Incorporated
400 Research Parkway
Meriden, CT 06450 U.S.A.
1-888-218-CUNO
www.cunofoodservice.com
3M is a trademark of 3M Company.
CUNO is a trademark of 3M Company used under license.
LIMITED WARRANTY
To Previous Page
Loading...
Need help?
General
