3M MT73H7A4410EU - Important Safety Cautions and Regulatory Approvals; Product Cautions and EN 352 Safety Statements; CE Marking and Product Conformity Declarations

2
• This product may be adversely affected by certain chemical
substances. Further information should be sought from the
manufacturer.
• These helmet mounted earmuffs are of Large size range.
Helmet mounted earmuffs complying with EN 352-3 are of
“medium size range” or “small size range” or “large size
range”. “Medium size range” helmet mounted earmuffs are
designed to t the majority of wearers. “Small size range” or
“large size range” helmet mounted earmuffs are designed to t
wearers for whom “medium size range” helmet mounted
earmuffs are not suitable.
• The output of the audio circuit of this hearing protector may
exceed the exposure limit level.
• The product shall not be used if it cannot be ensured that
the input voltage does not exceed the maximum value in Table
A:11.
CAUTION
• Risk of explosion if battery is replaced by an incorrect type.
• Do not charge batteries in temperatures above 45 °C (113 °F).
• Use only 3M™ PELTOR™ Battery ACK081 charged with
cable 3M™ PELTOR™ AL2AI connected to a 3M™ PELTOR™
Power supply FR08.
• With lithium-ion batteries, there is a risk of re and burns.
Do not open, crush, heat above 55 °C (131 °F), or incinerate.
• For noise environments dominated by frequencies below
500 Hz the C-weighted environmental noise level should be
used.
• Always use product-specic 3M replacement parts. Use of
unauthorized replacement parts may reduce the protection you
receive from this product.
• Obey the instructions given in this manual. Tampering with
the product may void the IP54 approval of this product.
NOTE
• When worn according to these user instructions, this hearing
protector helps reduce exposure to both continuous noises, such
as industrial noises and noises from vehicles and aircraft, as well
as very loud impulse noises, such as gunre.
It is difcult to predict the required and/or actual hearing
protection obtained during exposure to impulse noises. For
gunre, the weapon type, number of rounds red, proper
selection, t and use of hearing protection, proper care of hearing
protection, and other variables will impact performance. To learn
more about hearing protection for impulse noise, visit www.3M.
com.
• This earmuff is provided with level-dependent attenuation.
The wearer should check correct operation before use. If
distortion or failure is detected, the wearer should refer to the
manufacturer’s advice for maintenance and replacement of the
battery.
• This earmuff is provided with safety related audio input. The
user should check correct operation before use. If distortion or
failure is detected, the user should refer to the manufacturer’s
advice.
• This earmuff is provided with electrical audio input. The
wearer should check correct operation before use. If distortion
or failure is detected, the wearer should refer to the
manufacturer’s advice.
• This hearing protector limits the entertainment audio signal
to 82 dBA effective to the ear.
• Operating temperature range: –20 °C (–4 °F) to 55 °C
(131 °F)
• Storage temperature range: –20 °C (–4 °F) to 55 °C
(131 °F)
• Weight of hearing protector: 435 - 470 g
APPROVALS
Hereby, 3M Svenska AB declares that the Bluetooth
®
and
radio communication is in compliance with Directive 2014/53/EU
and other appropriate directives to fulll the requirements for
the CE marking. 3M Svenska AB also declares that the PPE
type headset is in compliance with Regulation (EU) 2016/425.
The applicable legislation can be determined by reviewing the
Declaration of Conformity (DoC) at www.3M.com/peltor/doc.
The DoC will also show if some other type approvals are also
applicable. When retrieving your DoC, please locate your part
number. The part number of your earmuffs can be found at
the bottom of one cup. An example can be seen in the picture
below.
The PPE is audited annually by SGS Fimko Ltd.,
Takomotie 8, FI-00380 Helsinki, Finland, Notied Body No.
0598 and type approved by PZT GmbH, Notied Body No.
1974, Bismarckstrasse 264 B, 26389, Wilhelmshaven,
Germany.
The product has been tested and approved in accordance
with EN 352-1:2002 / EN 352-3:2002, EN 352-4:2001/
A1:2005, EN 352-6:2002, EN 352-8:2008 or EN 352-1:2020,
EN 352-3:2020, EN 352-4:2020, EN 352-6:2020,
EN 352-8:2020.
The applicable version can be found in the DoC.
A copy of the DoC and additional information required in the
Directives can also be obtained by contacting 3M in the
country of purchase. For contact information, see the last
pages of this user instruction.
This product contains electrical and electronic components
and must not be disposed of using standard refuse collection.
Please consult local directives for disposal of electrical and
electronic equipment.
EN