To Next PageTo Next PageHow to deal with rubbing of rotating parts in ABB HT582247?
If you notice rubbing of rotating parts in your ABB Industrial Equipment, contact an ABB Turbocharging Service Station if there is any doubt about the extent of the rubbing. Also, have a dimension check carried out by an ABB Turbocharging Service Station.
What to do if ABB HT582247 has charge air pressure too low?
If the charge air pressure is too low, there could be several reasons. The air receiver or the gas piping between the engine and the turbine might be leaking. A poorly adjusted injection system also can cause this issue, so correct it. The manometer display might be providing a wrong reading, so replace the manometer, or the line to the manometer might be leaking, so repair the leak. A contaminated filter silencer causing excessive loss of pressure can also be the reason, so clean it. In some cases, the compressor/turbine might be damaged, which requires contacting an ABB Turbocharging Service Station. High exhaust counterpressure can also cause low charge air pressure, so clean or repair the boiler or exhaust silencer.
What causes fouling of the compressor in my ABB charger?
Fouling of the compressor in your ABB charger, due to the feeding in of ventilation gases, may result from: * Heavy fouling of the compressor components: Clean compressor. * Material of compressor wheel corroded: Check the fuel and its corrosive components, and change fuel if necessary.
What to do if my ABB Industrial Equipment is vibrating?
If your ABB Industrial Equipment is vibrating, it could be due to a rotor unbalance. In this case, you should contact an ABB Turbocharging Service Station. Another cause may be damaged turbine or compressor or damaged bearing.
What to do if ABB HT582247 has charge air pressure too high?
If the charge air pressure is too high, it could be due to a malfunctioning or poorly adjusted injection system, so repair or correct it. The engine performance might also be higher than expected, so check engine performance. The manometer display might be providing a wrong reading, so replace the manometer.
What to do if the charge air pressure is too low in ABB HT582247 Industrial Equipment?
If your ABB Industrial Equipment experiences charge air pressure that is too low, several factors could be responsible. You can repair any leaks in the air receiver or correct a poorly adjusted injection system. Additionally, you should replace the manometer if the display is wrong, or repair the leak if the line to the manometer is leaking. Clean the filter silencer if it is contaminated, causing excessive pressure loss. Finally, clean or repair the boiler or exhaust silencer if the exhaust counterpressure is too high.
Why is my ABB Industrial Equipment having a sluggish start-up?
If your ABB Industrial Equipment experiences a sluggish start-up, it could be due to a few reasons. The turbocharger might be contaminated and need cleaning. Alternatively, there may be damage to the bearing, in which case you should contact an ABB Turbocharging Service Station. Other potential causes include a rubbing rotor or a foreign object present in the turbocharger.
Why is there a reduction in speed in my ABB charger?
A reduction in speed in your ABB charger can stem from: * Defects of connected cylinders when pulse charging: Contact the enginebuilder. * Heavy contamination of the turbine: Clean it. * Damaged rotor components or bearing: Contact an ABB Turbocharging Service Station. * Defects such as leaks in the exhaust gas pipes or charge air ducts: Make repairs.
Why is the charge air pressure too high in my ABB charger?
If the charge air pressure is too high in your ABB charger, it may be due to: * A malfunctioning injection system: Repair it or contact the manufacturer. * A poorly adjusted injection system: Correct it. * Engine performance higher than expected: Check engine performance. * Manometer display wrong: Replace the manometer.
Why is the charge air pressure too low in my ABB charger?
If the charge air pressure is too low in your ABB charger, several factors could be responsible: * Air receiver leaking: Make repairs. * Gas piping between the engine and the turbine leaking. * Poorly adjusted injection system: Correct it. * Poorly adjusted valve control. * Manometer display wrong: Replace the manometer. * Line to manometer leaking: Repair the leak. * Contaminated filter silencer: Clean it because it causes excessive pressure loss. * Damaged compressor/turbine: Contact an ABB Turbocharging Service Station. * High exhaust counterpressure: Clean or repair the boiler or exhaust silencer.
General| Manufacturer | ABB |
|---|---|
| Rated Current | 16 A |
| Rated Voltage | 230/400 V AC |
| Breaking Capacity | 6 kA |
| Poles | 1 |
| Mechanical Life | 20000 operations |
| Electrical Life | 10000 operations |
| Mounting | DIN rail |
| Standards | IEC 60898-1 |
