Acson AMSD-A Series - Page 18

AMST SERIES COOLING ONLY
OUTDOOR UNIT
AMST101010A AMST151515A
INDOOR UNIT
3 x AWMS10F 2 x AWMS10F AWMS15F AWMS10F 2 x AWMS15F 3 x AWMS15F
kcal/h
3 x 2394 2 x 2394 3,200 2,394 2 x 3,200 3 x 3200
W
3 x 2784 2 x 2784 3,721 2,784 2 x 3,721 3 x 3721
Btu/h
3 x 9500 2 x 9500 12,700 9,500 2 x 12,700 3 x 12700
W 2,616 4,176
A 11.1 18.4
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE
HIGH CFM/LPS
300 / 141.6 300 / 141.6 300 / 141.6 300 / 141.6 300 / 141.6 300 / 141.6
MEDIUM CFM/LPS
230 / 108.6 230 / 108.6 270 / 127.4 230 / 108.6 270 / 127.4 270 / 127.4
LOW CFM/LPS
190 /89.7 190 /89.7 230 / 108.6 190 /89.7 230 / 108.6 230 / 108.6
FAN MOTOR
4 POLES x 12W 4 POLES x 10W
INPUT POWER W 30 25
RUNNING CURRENT A
0.13 0.11
FAN MOTOR PROTECTION
MATERIAL
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg
SOUND PRESSURE LEVEL ( H/M/L ) dBA
38 / 35 / 31 38 / 34 / 30
ROOM TEMPERATURE
CONTROL AIR DISCHARGE
OPERATION
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
PACKING HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
COMPRESSOR TYPE
NUMBER
CAPACITOR µF
LOCK ROTOR AMP A 25 18.9
INPUT POWER W 771 1290 / 1290
PROTECTION DEVICE
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A
RATED OUTPUT POWER W
RATED INPUT POWER W
MATERIAL
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg
97 109
SOUND PRESSURE LEVEL dBA
61 62
MATERIAL
CASING THICKNESS mm/in
FINISHING
TYPE
SIZE LIQUID mm/in
GAS mm/in
12.7 / 1/2 9.52 / 3/8
PACKING HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
kg 3 x 0.800 2 x 0.800 0.825 0.800 2 x 0.825 3 x 0.825
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ARI 210/240-94
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW:
a) COOLING - 26.7°C DB / 19.4°C WB INDOOR AND 35°C DB OUTDOOR
4) SOUND PRESSURE LEVEL IS ACCORDING TO JIS B 8615 STANDARD.
POSITION OF THE MEASUREMENT POINT IS 1.0 m IN FRONT AND 1.0 m BELOW THE UNIT.
5) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
4 POLES x 10W 4 POLES x 12W
38 / 35 / 31
3
AUTOMATIC LOUVER (UP & DOWN) & MANUAL ADJUST GRILLE (LEFT & RIGHT)
LCD WIRELESS MICRO COMPUTER REMOTE CONTROL
38 / 34 / 30
MICROCOMPUTER CONTROLLED THERMOSTAT
BUILT IN THERMAL FUSE
0.28 / 0.011
25 30
0.13
MODEL
FAN
INDOOR UNIT
COIL
NOMINAL
COOLING
179 / 7.0
290 / 11.4
9.5
ALUMINIUM (HYDROPHILIC SLIT FIN)
0.11 / 0.0043
220 ~ 240 / 1 / 50
R22 / OUTDOOR CAPILLARY TUBE
FAN
815 / 32.1
0.92
OVERLOAD PROTECTION
16 / 0.63
WASHABLE SARANET
371 / 14.6
ANTI FUNGUS CROSS FLOW FAN
0.193 / 2.08
0.11
SEAMLESS INNER GROOVED COPPER
7.0 / 0.276
2
18
AMST101015A
13.6
AMST101515A
3,136 3,656
16.0
875 / 34.4
269 / 10.6
ROTARY
30
18.9 25
SEAMLESS BARE COPPER
PROPELLER / DIRECT
GLASS REINFORCED ACRLY STYRENE RESIN
482.6 / 19
150
228
3
14
0.50 / 5.39
9.52 / 3/8
0.33 / 0.013
ALUMINIUM (SLIT FIN TYPE)
0.12 / 0.005
611 / 24.1
GALVANISED MILD STEEL
1.0 - 1.2 / 0.039 - 0.047
EPOXY POLYESTER POWDER
6.35 / 1/4
9.52 / 3/8 12.7 / 1/2
FLARE VALVE
61 62
1,194 / 47.0
CAPACITY
AIR FLOW
PIPE COMPCOIL
TUBEFIN TUBEFIN
631.7 / 24.9
RATED TOTAL POWER CONSUMPTION
RATED TOTAL RUNNING CURRENT
REFRIGERANT CHARGE
OUTDOOR UNIT
960 / 37.8
437 / 17.2
824 / 32.4
101 105
17