Why is my Acson AWM 20G Air Conditioner dripping water inside?
If you notice condensation on the front air grille of your Acson Air Conditioner's indoor unit, it is likely due to air humidity after prolonged operation. To address this, increase the temperature setting and operate the unit at a high fan speed.
Why does my Acson AWM 20G smell bad?
If your Acson Air Conditioner emits a bad odor, it might be due to particles like cigarettes, smoke, or perfume that have adhered to the coil. Contact your nearest dealer for assistance.
What to do if my Acson Air Conditioner won't turn back on after a power outage?
If your Acson Air Conditioner does not restart after a power failure, turn on the unit using the wireless or wired controller.
Why is my Acson Air Conditioner remote display dim?
If the wireless controller display for your Acson Air Conditioner is dim, the batteries may be discharged and need replacing. Also, check that the batteries are correctly inserted and that the assembly is properly done.
How to improve airflow in my Acson AWM 20G Air Conditioner?
If your Acson Air Conditioner isn't providing sufficient airflow or cooling, several factors could be at play. First, check and clean the air filter if it's dirty. Ensure that all doors and windows are closed to prevent outside air from interfering with cooling. Confirm that neither the air suction nor the discharge vents of the indoor and outdoor units are blocked. Finally, verify that the temperature setting is appropriately low for effective cooling.
Why does my Acson AWM 20G Air Conditioner compressor keep running?
If your Acson Air Conditioner's compressor is running continuously, it might be caused by a dirty air filter, which requires cleaning. Alternatively, the temperature setting may be too low for cooling or too high for heating. Adjust the temperature setting accordingly.
Why on heating cycle, warm air does not come out of Acson Air Conditioner?
If warm air does not come out of your Acson Air Conditioner during the heating cycle, it might be in defrost mode. The heating operation will resume once the defrost cycle is complete.
Why is the airflow too slow in my Acson AWM 20G Air Conditioner, or why isn't the room cooling sufficiently?
If the airflow from your Acson Air Conditioner is too slow, or the room isn't cooling enough, consider these possibilities: * The air filter might be dirty, so try cleaning it. * Open doors and windows can impact performance; ensure they are closed. * Obstructions can block air suction and discharge of both indoor and outdoor units; clear any blockages. * The temperature setting may be too high; try setting a lower temperature.
General| Brand | Acson |
|---|---|
| Model | AWM 20G |
| Category | Air Conditioner |
| Language | English |
Explains the coding system for indoor unit model numbers.
Explains the coding system for outdoor unit model numbers.
Highlights the ease of installing the wall-mounted fan coil unit.
Describes the compact design that maximizes floor space usage.
Mentions improved comfort through whisper-quiet tangential fan operation.
Details adjustable air discharge and double louver design.
Covers easy access for cleaning fan blower and electrical components.
Describes the functions and range of the LCD transmitter.
Explains the dry mode and its effectiveness.
Details the 3-fold structure heat exchanger for efficient exchange.
Highlights the energy efficiency and output of the rotary compressor.
Explains the fault detection via LED blinking for easy troubleshooting.
Specifies the allowable working temperature and humidity ranges for the unit.
Illustrates the refrigerant flow for cooling and heatpump models.
Details the functions and operations of the G12 remote controller.
Explains the LED indicator lights for normal and fault conditions.
Describes hot start, hot keep, hot spurt, and turbo modes for heating.
Details overload and frost prevention mechanisms for the unit.
Provides a visual representation of the indoor and outdoor unit installation.
Specifies requirements for selecting the indoor unit location and space.
Lists requirements for selecting the outdoor unit location for optimal cooling.
Details minimum clearance requirements for outdoor unit installation.
Provides guidance on field wiring rules and electrical connection precautions.
Lists essential safety checks before wiring the unit.
Tabulates recommendations for refrigerant piping based on model.
Describes the procedure for creating flare connections for piping.
Details orifice kit installation based on available space.
Provides a table for calculating additional refrigerant charge based on piping length.
Introduces R410A refrigerant and its characteristics.
Lists R410A components and explains its properties and precautions.
Lists essential checks for tubing, compressor oil, and tools for R410A.
Provides guidelines for handling and installing R410A systems.
Presents sound pressure levels for the wall-mounted fan coil unit.
Displays noise criteria (NC) curves for various models and fan speeds.
Provides detailed specifications for R22 cooling-only models.
Details specifications for R22 heatpump models.
Presents specifications for R410A cooling-only models.
Details specifications for R410A heatpump models.
Lists the component specifications for R22 cooling-only units.
Lists component specifications for R22 heatpump units.
Lists component specifications for R410A cooling-only units.
Lists component specifications for R410A heatpump units.
Explains how to calculate capacity using interpolation and extrapolation.
Provides detailed cooling performance tables for R22 models.
Provides detailed cooling performance tables for R410A models.
Performance data tables for R22 heatpump cooling mode.
Performance data tables for R22 heatpump heating mode.
Provides dimensional drawings and measurements for indoor units.
Provides dimensional drawings and measurements for outdoor units.
Lists electrical specifications for indoor units, including motor and compressor data.
Details electrical specifications for outdoor units, including motor and compressor data.
Provides electrical specifications for the compressor unit.
Illustrates the wiring diagrams for cooling-only models.
Shows the wiring diagrams for heatpump models.
Outlines maintenance steps required after a period of extended shutdown.
Provides guidance for diagnosing common air conditioner issues and their causes.
Shows exploded views and lists parts for various indoor unit models.
Provides exploded views and parts lists for various outdoor unit models.
To Next Page
