Front Side Marker/Parking Lights LED
Front Turn Signal Lights
24 W
(PWY 24 W Amber/Silver)
Side Turn Signal Lights
(on Door Mirrors)
LED
Brake/Taillights/Rear Side Marker
Lights
LED
Brake/Taillights
Back-Up Lights
21 W
Rear Turn Signal Lights
High-Mount Brake Light
LED
Rear License Plate Lights
Interior Lights
Front and Rear Map Lights
LED
Front and Rear Ambient LightsLED
Vanity Mirror Lights 1.4 W
Center Pocket Light LED
Door Courtesy Lights
3.4 W
Console Compartment Light1.4 W
Glove Box Light 1.4 W
Door Inner Handle Lights LED
Trunk Lights 5 W
LED
LED
21 W
t
Recommended
·Genuine Acura Motor Oil 0W-20
·API Premium-grade 0W-20 detergent oil
Capacity
Change 4.2 US qt (4.0 ℓ)
Change
including
lter
4.4 US qt (4.2 ℓ)
Specied Acura Long Life Antifreeze/Coolant Type2
Ratio 50/50 with distilled water
Capacity Change 3.3 US qt (3.1 ℓ)
Capacity
1.61 US gal (6.1 ℓ)
(change including the remaining
0.225 US gal (0.85 ℓ) in the reserve tank)
Pressure
psi (kPa [kgf/cm
2
])
60 (420 [4.2])
Wheel Size
Regular 17 x 7 1/2J
Compact Spare
*1
17 x 4T
4-cylinder models
Testing of Readiness Codes
Your vehicle has “Readiness Codes” as part of the onboard self-diagnostic system.
Some states refer to these codes as a test to see if your vehicle’s emissions
components are working properly. The codes may not be read if you go through the
testing just after the battery has gone dead or been disconnected.
To check if they are set, set the power mode to ON without starting the engine.
The malfunction indicator lamp will come on for several seconds. If it goes off, the
readiness codes are set. If it blinks ve times, the readiness codes are not set.
If you are required to have your vehicle tested before the readiness codes are set,
prepare the vehicle for retesting by doing the following:
1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.
3. Make sure the ambient temperature is between 40°F and 95°F (4°C and 35°C).
4. Start the engine without touching the accelerator pedal, and let it idle for 20
seconds.
5. Keep the vehicle in Park. Increase the engine speed to 2,000 rpm, and hold it
there for about 3 minutes.
6. Let the engine idle with your foot off the accelerator for 20 seconds.
7. Select a nearby, lightly traveled major highway where you can maintain a speed
of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway
with the vehicle in Drive. Do not use cruise control. When traffic allows, drive
for 90 seconds without using the accelerator pedal. (Vehicle speed may vary
slightly; this is OK.) If you cannot do this for a continuous 90 seconds because of
traffic conditions, drive for at least 30 seconds, then repeat two more times (for
a total of 90 seconds).
8. Drive in city/suburban trafc for at least 10 minutes. When trafc conditions
allow, let the vehicle coast for several seconds without using the accelerator
pedal or the brake pedal.
9. Park the vehicle and leave the engine off for 30 minutes.
The readiness codes are erased when the battery is disconnected, and set again
only after several days of driving under a variety of conditions.
If a testing facility determines that the readiness codes are not set, you may be
requested to return at a later date to complete the test, or see your dealer.
SPECIFICATIONS
To Next Page
Loading...
