RADIUS WEATHER STRIP
RADIUS
FLAT
AVAILABLE FACEPLATES
3b
FOR APPLICATIONSTHAT REQUIRE
RETRACTION OF THE DEADBOLT
AND DEADLATCH FROM BOTH
SIDES OF THE DOOR.
REMOVE THE
INTER-CONNECT CAM, AND INSTALL
THE OPTIONAL DOUBLE
INTER-CONNECT CAM.
4.200
1.125
ONE WALL ONLY
2.310
1.212
1.160
3.306
5.025
.500
ONE WALL ONLY
FOR
ELECTRIFIED OPTION
1.125
THRU ONE
WALL ONLY
2.520
.196
ONE WALL ONLY
4x,
.177
.968
.928
.928
.968
BACKSET
FOR INSWING DOORS USE SMALL FORMAT LEVERS (4600)
AND REFER TO 4600 INSTRUCTION WITH 2190
6.885
1.010
R
.156
4x
6.375
1.594
C
L
OF
CYLINDER
OUTSWING LOCK STILE PREPARATION ONLY
4.200
.938
.968
1.250
BOTH WALLS
FOR CYLINDER
.875
ONE WALL ONLY
2.238
.177
.196
ONE WALL ONLY
4x,
.177
.196
ONE WALL ONLY
1.212
1.160
3.390
2.520
.968
.938
BACKSET
5.375
4.645
1.447
.080
2 PLS
C'SNK FOR #10
FLAT HD SCREW
.218
.572
ALUMINUM FRAME
C
L
OF
CYLINDER
DEADLATCH
IN DOOR
C
L
2101 STRIKE PLATE
SHOWN
C
L
OF
STRIKE PLATE
(2 15/32")
FOR RADIUS FACEPLATE
WITH WEATHERSEAL ONLY !
- WITH A SMALL FLAT HEAD
SCREWDRIVER, PRY OFF
BEVEL TABS AS SHOWN.
LHR BEVEL
RHR BEVEL
FLAT or RADIUS
- YOU WILL ALSO HAVE TO RE-ORIENT
THE INTER-CONNECT CAM:
a)
LOOSEN THE #6-32 FLAT HEAD SCREW
AT THE BOTTOM OF THE LOCK.
b)
ROTATE THE INTER-CONNECT CAM
TO THE SAME DIRECTION AS THE
LATCH BOLT BEVEL.
RETIGHTEN THE #6-32 FLAT HEAD
SCREW TO COMPLETE THE
OPERATION.
#6 x1/2"
BOLT SCREW
LATCH
BOLT
1-1/2" BACKSET
SHOWN
3a
TO CHANGE THE HANDING
ON LATCH BOLT:
- DEPRESS THE LATCHBOLT UNTIL BOLT SCREW CAN BE
SEEN THROUGH CASE HOLE. (1-1/2" BACKSET ONLY).
- REMOVE BOLT SCREW AND ORIENT LATCH BOLT TO
THE OPPOSITE HAND.
- DEPRESS THE LATCH BOLT UNTIL THE COUNTERSINK
HOLE ON THE LATCH BOLT CAN BE SEEN THROUGH THE
CASE HOLE AS SHOWN IN
FIG.1.
- REINSERT BOLT SCREW AND TIGHTEN TO 22 - 27 IN-LB.
#1-64 x 1/4"
FLAT HEAD SCREW
INTER-
CONNECT CAM
BACK VIEW
BEVELED
SIDE SHOULD
FACE THE SAME
DIRECTION AS THE
INTER-CONNECT
CAM
LATCH
BOLT
#6-32
FLAT HD
SCREW
a
b
1-1/8 BACKSET
6.375
1.340
2x
#10-32
ONE WALL ONLY
BACK OF LOCK STILE
DOUBLE INTER-
CONNECT CAM
(P/N 27-0268)
3b
1-1/2 BACKSET
FIG.1
STRIKE PREPARATION
BEVEL TABS ADJUSTMENT
- ROTATE BEVEL TABS TO DESIRED HANDING.
USING THE BEVEL ADJUSTMENT ALLOWS THE FLAT.
FACEPLATE TO WORK IN BEVEL STILES
( INTERIOR TRIM )
( EXTERIOR TRIM )
- APPLY STICK ON TEMPLATE OVER CYLINDER BACKSET CENTER LINE.
NOTE: EACH TEMPLATE IS LABELED FOR OUTSIDE OR INSIDE TRIM.
- CENTER PUNCH ALL HOLES.
- DRILL HOLES AT CENTER PUNCH LOCATIONS. REMOVE TEMPLATE.
- INSTALL 2190 PER INSTALLATION INSTRUCTIONS.
1
32
TOOLS NEEDED:
- 5/64 ALLEN WRENCH
- 3/32 ALLEN WRENCH
- 1/8 ALLEN WRENCH
- #9 DRILL BIT (.196 Ø)
- #16 DRILL BIT (.177 Ø)
- 7/8 DRILL BIT (.875 Ø)
- 1-1/8 DRILL BIT (1.125 Ø )
INSTALLATION OF STRIKE
- INSERT MOUNTING BACK PLATE BEHIND JAMB AND FASTEN WITH
#10 FLAT HEAD SCREWS.
- INSERT TRIM BOX WITH 2101 STRIKE PLATE AND FASTEN WITH
#10 FLAT HEAD SCREWS TO BACK PLATE AS SHOWN.
3a
TO BLOCK HOLDBACK FEATURE:
- INSTALL #1-64 x 1/4" FLAT HEAD
SCREW INTO CASE AS SHOWN
BEFORE INSTALLING IN DOOR.
Page of
1
3
INSTALLATION INSTRUCTIONS
Rev.
Appvd: BC
Date:
ECN: 11883
Date: 02/09/12
D
2190 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET
80-0180-410
Adams Rite Manufacturing Co.
260 Santa Fe Street,
Pomona, CA 91767
Phone: 909-632-2300
Fax: 909-632-2369
www.adamsrite.com
02/03/2012
To Next Page
Need help?
General
