Adayo M9920 - General Operation; Sound Setting

2
PANEL CONTROLS
1. - Press to eject disc.
2. - Band switch:
FM1 -> FM2 -> FM3 -> AM1 -> AM2
- Dial / Receive / Transfer call (in BT mode)
3. Power / Toggle the audio source
4. - Previous / next track
- Search (long press)
5. - Unlock the front panel.
6. - Scan play / Preset scan
- Auto memory store (long press)
7. - Button 1: Scan play / Preset station 1
- Button 2: Repeat play / Preset station 2.
- Button 3: Random play / Preset station 3.
- Button 4: Play / Pause / Top play (long press)
/ Preset station 4.
- Button 5: Previous folder / Preset station 5.
10 tracks down (long press) /
- Button 6: Next folder / Preset station 6.
10 tracks up (long press) /
8. - MUTE
- Sound effect setting
9. - Display switch
- System setup (long press)
10. - Aux-in jack
11. - USB connector
12. - CD disc slot
13.-Adjustvolumelevel/Conrm(press)
14. - MP3/WMA mode – Search function.
- CD mode – No function.
- RADIO mode – No function.
- AUX mode – No function.
- USB mode – Search function.
- BT mode – Reject / Terminate call.
MUTE
EQ
3
GENERAL OPERATION
Power On/Off Button
Press the [SRC / ] button to turn the unit on
when the vehicle ignition switch is on. Press
and hold the button to turn the unit off.
Adjust Volume level
Rotate the volume knob to adjust volume
level. Rotate it clockwise to increase and
counterclockwise to decrease the volume.
Audio Mute
Press the [ MUTE ] button to mute the volume
from the system. “MUTE” will appear on the
display panel and the volume will be muted.
Press the [ MUTE ] button again, or rotate
or press the VOL/MENU control to return the
volume level to the setting in use before the
Mute function was activated.
Mode Button (SRC)
Press the [SRC / ] button to change
between Radio, DISC (when disc is in), USB
(when USB is connected), Card(when SD/
MMC card is in), A2DP(when BT is connected)
or AUX play.
Auxiliary Input
To access an auxiliary device:
1. Connect the portable audio player to the
AUX interface on the front panel.
2. Press the [SRC / ] button to select Aux-
In mode.
Press SRC again to cancel Aux-In mode and
go to the next mode.
Display Selector (DISP)
This unit can display either the clock time
or radio frequency/CD player functions.
Ordinarily, the radio frequency or CD
player track indication is displayed, but the
unit will display the time when the DISP
button is pressed. The time will display for
approximately 5 seconds then return to the
radio or CD player function display.
Press and hold the [ MUTE ] button to enter
sound effect setting mode. First press shows
current EQ. Rotate the volume knob to
changes BEAT EQ in this order:
OFF -> POP -> CLASSIC -> ROCK -> JAZZ
-> CUSTOM
Rotate the volume knob to changes CUSTOM,
and press the volume knob, then press [
]
or [ ] button to select it including: BAS-G
-> TRE-G, rotate the volume knob to select a
value.
BAS-G / TRE-G: (-7)- (+7)
Press and hold the [ MUTE ] button, then
press [
] or [ ] button to select USER
preset including:
BALANCE -> FADER -> LOUD, rotate the
volume knob to select a value.
BALANCE:LEFT 1-7->CENTER->RIGHT 1-7
FADER:FRONT 1-7->CENTER->REAR 1-7
LOUD: ON/OFF
SOUND SETTING