ADEMCO VISTA-20SE Installation Instructions

100 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

VISTA-20

SE

2-PARTITIONED

SECURITY SYSTEM

INSTALLATION

INSTRUCTIONS

®

Principal changes between the VISTA-20SE and the

former VISTA-20 are indicated by margin lines.

N7526V4 Rev B 4/99

WWW.DIYALARMFORUM.COM

Table of Contents

Default Chapter1
- Security System1
- Recommendations for Proper Protection2
- Table of Contents3
- Conventions Used in this Manual6
Section 1. GENERAL DESCRIPTION7
Section 2. INSTALLING the CONTROL10
- Mounting the Cabinet10
- Installing the Lock (if Used)10
- Figure 1. Installing the Cabinet Lock10
- Mounting the Control's Circuit Board Alone in the Cabinet11
- Mounting Control and RF Receiver Circuit Boards Together in the Cabinet11
- Figure 2. Mounting the PC Board11
- Figure 3. Mounting the PC Board & RF Receiver Together in the Cabinet11
- Standard Phone Line Connections12
- Wiring the AC Transformer12
- Figure 4. Telephone Line Connections12
- Installing the Back-Up Battery13
- Earth Ground Connections13
- Figure 5. Connection of 4300 Transformer to the Control Board13
Installing Remote Keypads14
- Keypads that May be Used14
- Wiring the Keypads14
- Mounting the Keypads15
- Using a Supplementary Power Supply to Power Additional Keypads15
- Figure 6. Keypad Connections to the Control Board15
- Preliminary Check-Out Procedure16
- Figure 7. Using a Supplementary Power Supply16
Basic Hard-Wired Zones 1-817
- Installing the Hard-Wired Zones17
- Check-Out Procedure for Hard-Wired Zones20
Wired Zone Expansion (4219, 4229)21
- Installing Zone Expansion Units21
  - Connections and Set-Up21
  - Figure 11. Wiring Connection, 4219 & 4229 (4229 Shown)21
- Check-Out Procedure for Wired Expansion Zones22
Wireless Zone Expansion (5800 System)23
- General Information23
  - Receiver Supervision23
  - House Identification23
- Installing the 5881/5882 RF Receiver23
- Installing the 5800TM Module25
  - Mounting the 5800TM Module25
  - 5800TM Wiring Connections25
- 5800 Series Transmitters25
- Using the Transmitter Sniffer Mode26
- 5800 Series Transmitters Table27
Relay Outputs & Powerline Carrier Devices29
- Relay/Powerline Carrier Device Basics29
- Nos. 4204 and 4229 Output Relay Modules29
  - 4204/4229 Setup29
- Powerline Carrier Devices30
Section 8. 4285 PHONE MODULE32
- Installing the Phone Module32
- Checking the Operation of the 4285 Phone Module35
Section 9. EXTERNAL SOUNDERS36
- Compatible Sounders36
- Sounder Connections37
- Testing the Sounder37
- Figure 17. Typical Sounder Wiring37
Section 10. LONG RANGE RADIO38
- General Information38
- Connection38
- Figure 18. Long Range Radio Connections38
Section 11. AUDIO ALARM VERIFICATION (AAV) UNIT39
- General Information39
- Wiring Connections39
- Figure 20. Connection of AAV Unit When Not Using a 4285 Phone Module40
- Figure 21. Connection of AAV Unit When also Using a 4285 Phone Module40
Section 12. FINAL POWER up41
- Earth Ground Connections41
- Connecting the Back-Up Battery41
  - Calculating the Battery Size Needed41
  - Making the Battery Connections42
- Auxiliary Device Current Draw Worksheet42
Section 13. MECHANICS of PROGRAMMING43
- General Programming Information43
- Entering Program Mode43
- Programming a Data Field43
- Reviewing a Data Field/Erasing an Entry in a Data Field44
- Interactive Mode Programming ( ✱ 56, ✱ 80, ✱ 82, and ✱ 83)44
- Loading Factory Defaults44
- Programming System Setup Fields44
- Exiting the Programming Mode44
Section 14. ZONE RESPONSE TYPE DEFINITIONS45
Section 15. DATA FIELD DESCRIPTIONS47
Programming Form57
Section 16. ZONE PROGRAMMING (*56 Menu Mode)57
Section 17. OUTPUT DEVICES (*80 Menu Mode)61
Section 18. ZONE LISTS (*81 Menu Mode)65
Section 19. ALPHA DESCRIPTION PROGRAMMING (*82 Menu Mode)66
- Assigning Zone Descriptors66
- Entering Zone Descriptors (in Program Menu Mode ✱ 82)66
- Alpha Descriptor Programming66
- Adding Custom Words69
- Alpha Vocabulary List (for Entering Zone Descriptors)70
- Character (ASCII) Chart70
Section 20. USING SEQUENTIAL MODE (*83 Menu Mode)71
Section 21. REMOTE PROGRAMMING and CONTROL (DOWNLOADING)74
- General Information74
- Equipment Required74
- Inititial Download74
- Remote Programming Information75
- Remote Programming Advisory Notes75
Section 22. SYSTEM COMMUNICATION76
- Report Code Formats76
- Table of Contact ID Codes78
Section 23. SYSTEM OPERATION79
- Security Codes79
- Keypad Functions80
- Trouble Conditions82
Section 24. TESTING the SYSTEM83
- Test Procedure83
- To the Installer84
Section 25. TROUBLESHOOTING GUIDE85
- Contacting Technical Support in the Event of Problems87
- Regulatory Agency Statements88
Section 26. SPECIFICATIONS & ACCESSORIES89
- Specifications89
- Accessories (Compatible Devices)91
APPENDIX A. 5800 RF System Wireless Transmitters, Input Loop Identification Diagrams92
Index93
Limitations of this Alarm System98
Summary of Connections99
- Figure 22. VISTA-20SE Summary of Connections99
Limited Warranty100

Other manuals for ADEMCO VISTA-20SE

User Guide52 pages

User Manual4 pages

Questions and Answers:

Need help?

Do you have a question about the ADEMCO VISTA-20SE and is the answer not in the manual?

ADEMCO VISTA-20SE Specifications

General

Brand	ADEMCO
Model	VISTA-20SE
Category	Security System
Language	English

Related product manuals

Preview: ADEMCO Vista-20

ADEMCO Vista-20

Preview: ADEMCO VISTA-20PS Series

ADEMCO VISTA-20PS Series

ADEMCO VISTA-25

ADEMCO VISTA-250FBP

Preview: ADEMCO VISTA

Preview: ADEMCO VISTA-50P

ADEMCO VISTA-50P

Preview: ADEMCO VISTA-100

ADEMCO VISTA-100

Preview: ADEMCO Vista-10SE

ADEMCO Vista-10SE

ADEMCO Vista-10SEa

Preview: ADEMCO VISTA-128FBP

ADEMCO VISTA-128FBP

ADEMCO Vista 4140XMPT

ADEMCO Vista 4140XMPT2