Adleepower AM-60L User Manual (English)

Questions and Answers:

E
Erika HamiltonAug 20, 2025
What to do if my Adleepower AM-60L show driver overheat, over voltage, or over current?
- R
  robertgarciaAug 21, 2025
  If your Adleepower DC Drives are showing driver overheat, over voltage, or over current, you should: * Check the input voltage to ensure it's not too high. * Check the cooling condition of the drives. * Check the motor loading to ensure it's not overloaded. * Inspect the wiring and plugs between the motors and drives for any U, V, W shortages. * Examine the acceleration and deceleration time settings. * Verify the CW, CCW, and stop operation frequency. * Check the inertial load, as the motors may be getting traction from the loading.
M
Michael BurnettAug 22, 2025
What to do if Adleepower AM-60L motor overheat?
- D
  Douglas DeleonAug 22, 2025
  If the motor is overheating, check the motor's cooling condition and ensure that the motor is not overloaded.
A
Anthony HolmesAug 25, 2025
What to do if Adleepower AM-60L display 'Mod Bus fail'?
- D
  danajohnsonAug 25, 2025
  If your Adleepower DC Drives display 'Mod Bus fail', verify that all drive settings are consistent, including address, communication speed, and data format. Also, ensure that the communication wires are connected correctly (A to A and B to B).
B
benjaminedwardsAug 26, 2025
What to do if Adleepower AM-60L DC Drives show 'Over load'?
- P
  pamelabradfordAug 26, 2025
  If your Adleepower DC Drives indicate an overload, check the motor loading. Consult the specification table for appropriate loading parameters.
G
Gary CarrilloAug 27, 2025
What to do if Adleepower DC Drives show 'Over speed'?
- U
  umirandaAug 27, 2025
  If your Adleepower DC Drives are showing an over speed error, check for rapid reductions in load variation.
L
Lawrence ChenAug 29, 2025
What to do if the speed is too low on Adleepower AM-60L DC Drives?
- B
  Brittney ParksAug 29, 2025
  If the speed is too low on your Adleepower DC Drives, check for rapid increases in load variation.
P
pwoodsAug 31, 2025
What to do if Adleepower AM-60L show 'Motor lock protection'?
- B
  Brian FergusonAug 31, 2025
  If your Adleepower DC Drives are showing 'Motor lock protection', check for rotor lock and examine the load condition.
E
Erika DouglasSep 2, 2025
What to do if Adleepower AM-60L display 'F306 unconnect or RS485 fail'?
- S
  sydney74Sep 2, 2025
  If your Adleepower DC Drives display 'F306 unconnect or RS485 fail', connect the F306 to the RS485 port and press the STOP key to reset. Also, check the RS485 connection and set code address 100=0 or 3 to reset.
G
gallagherjacobSep 3, 2025
What does 'Source of speed command error' mean for Adleepower DC Drives?
- J
  Jared RobertsSep 3, 2025
  If you encounter a 'Source of speed command error' with your Adleepower DC Drives, it means the system is set at analog command, but the F306 keypad is being used to change the speed. Use CD19 to change the setting.
L
Laurie JimenezSep 5, 2025
What does 'Source of operation command error' mean for Adleepower AM-60L DC Drives?
- M
  mcrossSep 5, 2025
  If you are getting a 'Source of operation command error' on your Adleepower DC Drives, it indicates that terminal control, F306, and RS485 cannot be used simultaneously. Use the jumper to change the setting.