AEG BSS 4815 - General Operation; Switching Device On;Off

English
37
CAUTION:
Batteries must not be disposed of in the garbage. Please
bring used batteries to competent collection centers or
back to the dealer.
Reestablishing factory settings
Possible malfunctions during the operation may be remedied
by pressing the RESET button (2).
• Presstheresetbutton(RESET)ontheremotecontrolto
reset the electronics. The settings made by you will get
lost in the process.
General Operation
Switch device on/off
• Turnonthedeviceswiththepowerswitchontherear.Set
the POWER switch to the “ON” position.
• Withthe
button (14), you can switch the unit between
standby and operating mode. When in standby, two bars
are lit in the display.
• Toturnoffthedevices,setthepowerswitchPOWERon
the back side to the “OFF” position. To disconnect the
unit completely from the mains, pull the mains plug from
the socket.
NOTE:
After about 30 minutes without signal, or if the signal is too
weak, the device will automatically switch to standby.
Volume
By pressing the
/ buttons (7/10) you can adjust the desi-
red volume.
Infrared Remote Control
For wireless control within a distance of 5 m. If this range de-
creases, the battery has to be replaced. For proper operation
mind a clear view between the remote control and the sensor
on the device.
INPUT (1)
Press the INPUT button until the desired operating mode is
shown on the display. After 3 seconds the volume indicator
appear in the display again.
Sound Settings (4)
(Preset equalizer function) Different ssound modes are availab-
le (NORMAL, MUSIC, MOVIE).
NOTE:
If necessary, change the EQ setting in your playback unit to
create the best sound.
Adjusting basses and trebles (13)
The basses are adjusted with the BASS+/BASS- buttons.
The trebles are adjusted with the TREBLE+/TREBLE- buttons.
(3)
For immediate muting of the volume. The currently set
volumewillashinthedisplay.Press
again to cancel the
function.
Radio mode
1. Fully uncoil the wire antenna. Insert the dipole antenna
into the FM jack (1).
2. Manual scan for radio stations:
Brieypressthe>>/<< button (6), until you have found
the radio station which you are looking for. If you keep
one of the buttons pressed down, the device will search
totheprevious,respectivelynextradiostation.
Preset station:
1. Using the CH+ or the CH- button, select the program
channel space before the program channel in which
you want to store a radio station. Example: To store
a station in the program channel CH02, set the pro-
gram channel CH01.
2. Search for the desired radio station with the >>/<<
buttons (6).
3. To store the radio station, keep the CH+ button
(11) pressed down for ca. 3 seconds. For the listed
example,CH02willappearbrieyinthedisplayand
the radio station is stored.
3. If the reception is too weak and there is interference on
the received station, try to improve the reception by
altering the position and uncoiling or coiling the antenna.
For FM stations, you can use the ST/MONO button (8) to
switch between mono and stereo reception. We recom-
mend that you switch to mono in case of bad reception.
The message “ST” is shown on the display for stereo
reception. During reception in mono “SOFF” will appear
brieyinthedisplay.
Select the preset radio station
The preset radio stations can be selected by repeatedly
pressing the CH+/CH- button (11).
Playing back music files
You have two possibilities to replay own music files with the
device: Wired or wireless via Bluetooth.
By cable (Cable not included)
The device has three connection possibilities: COAXIAL (2),
PC (3), and OPTICAL (4).
1. If required, use a suitable adapter (not included).
Connecttheexternaldeviceasfollows:
• Withacinchcable(RCA)totheCOAXIALjack(2).
• Witha3.5mmstereojackplugtothePCsocket(3).
• WithaTOSLINKcabletotheOPTICALjack(4).
2. Depending on the connection used, press the INPUT
button (1) until COA, PC, or OP appears in the display.