English
38
Playing CDs
NOTE:
Observe the following operation for the replay of CD’s in
the MP3 format! The device is not MP3 capable. The CD
will however start to turn, but the sound cannot be repro-
duced.
This is how you play a CD
1. Select the CD mode with the FUNCTION button (13/27).
The following will appear in the display “- -”.
2. Press the OPEN/CLOSE button (9/26) to open the CD
tray.
3. Place the CD into the CD tray with the label side up.
Press the OPEN/CLOSE button once more to close the
CD tray again.
4. After a few seconds the total number of songs/tracks is
shown in the display.
5. Press the PLAY/PAUSE (
) button (10/24). The CD will
play from the first title. The current title number and the
notification “ ” are shown on the display.
6. In order to remove a CD, please press the STOP (
)
button (8/34), open the CD compartment and lift the CD
out carefully.
Always keep the CD tray closed.
NOTE:
• Ifadiscisinsertedthewrongwayaround,respectivelyif
no disc is inserted, then the message “- -” will blink and
“NO” appears on the display.
• PlaybackofCDsproducedbytheusercannotbe
guaranteed due to the large variety of software and CD
media available.
• Pleasenote:
There are many burning and compression methods,
as well as quality differences between CDs and burned
CDs.
The music industry furthermore does not observe any
xedstandards(copyrightprotection).
For these reasons, in rare cases there may be problems
when playing CDs. This is not a malfunction of the
device.
Description of the CD buttons
PLAY/PAUSE ( ) (10/24)
Youcanbrieyinterruptandresumeplaybackusingthisbut-
ton. The symbol “
”willashonthedisplay.Pressingagain
continues playback.
F.FWD
/
REW (
/
/
/
) (6/7/33)
With F.FWD
(
/
)youcanjumptothenextorprevious
track etc.
• Ifthebuttoniskeptpresseddown,themachinestartsto
search through the tracks.
The
REW (
/
) button can be used as follows:
Pressonce= Thisstartsthecurrenttrackagainfromthe
beginning.
Presstwice= Thisjumpsbacktotheprevioustrack.
Pressthreetimes=Thisplaysthesongbeforeetc.Ifthebut-
ton is kept pressed down, the machine
starts to search through the tracks.
STOP (
) (8/34)
The CD stops.
REPEAT (5/23)
With a CD currently playing:
Pressonce= (the
emitsaxedlight)thecurrent
track is repeated continuously.
Presstwice= (theALL emitsaxedlight)thewhole
CD is played continuously.
Pressthreetimes=allfunctionsarecancelled.Thenormal
play mode is resumed.
Programmed Play
This can be used to program any desired sequence of tracks.
1. Press the STOP (
) button (8/34).
2. Press the MEM/PROG button (4/21). The memory
location “01” and the notification “PROG” will blink
in the display. Use the F.FWD / REW (
/
/
/
)
buttons (6/7/33) to select the desired track and then press
the MEM/PROG button again. The display changes to
memory slot 02.
3. SelectthenexttrackwiththeF.FWD / REW (
/
/
/
) buttons and press the MEM/PROG button again.
Repeat the procedure until all the desired tracks are
selected.
NOTE:
If the storage capacity of the titles to be programmed
has been reached, all the programmed titles will be
shown in sequence.
4. Press the PLAY/PAUSE (
) button (10/24). The playback
starts. The current title number, the notification “ ” and
“PROG” will be shown in the display.
5. Press once the STOP ( ) button to stop the playback
while retaining the program.
6. To play the programme back again, press the PLAY/
PAUSE ( ) button.
7. To delete the program, press the STOP ( ) button twice.
The PROG control lamp goes out.
The device stops automatically after all programmed titles
have been played. The indication PROG goes out and the
programmed sequence is deleted from the memory.
To Next Page
Loading...
