Quick Start Guide
First-Time Use / Admin Mode Setup
2
3
1
Aegis Secure Key 3.0
PINs must be a minimum length of 7 digits
with a maximum of 16 digits.
Cannot contain all consecutive numbers
or all the same numbers (e.g. 123456789,
987654321 or 11111111, 22222222, etc.)
Each Aegis Secure Key is shipped without a preset Personal
Identication Number (PIN.) To prepare the Key for use, the user
must rst establish an Admin PIN that is between 7and 16 digits
in length. This Admin PIN is used to set the Secure Key’s various
Admin features and also serves as the rst of two User PINS for
the Secure Key’s standard operation.
To Set Up the Admin PIN:
1. Wake up the Secure Key by pressing .
(BLUE and GREEN LEDs will glow solidly, indicating no Admin
PIN has been established.)
2. Press + 9 simultaneously.
(BLUE LED will glow solidly and GREEN LED will blink.)
3. Enter the PIN to be used as your Admin code and press .
(If PIN is accepted, BLUE LED will turn off momentarily and
GREEN LED will blink 3 times by itself, then will continue
blinking as the BLUE LED glows solidly.)*
4. Quickly re-enter that same PIN once more and press
(BLUE LED will turn off momentarily and GREEN LED will
illuminate for one second until replaced by the BLUE LED
glowing solidly, indicating that the Admin PIN has been set and
the Secure Key is in Admin mode, ready to add another User
PIN [see reverse] or for setting up features.)
5. To exit the Admin mode, press (RED LED will glow solidly) or
wait 30 seconds and Secure Key will return to sleep mode.
6. If no additional users are to be added or Admin features set,
Secure Key setup is now complete and ready for use.
* If PIN is unacceptable, Red LED will blink 3 times and
return to solid BLUE / blinking GREEN LEDs. Check “PIN
Requirements” section below and repeat step 3.
Note: It’s normal for this device to be warm to the touch during use.
PIN Requirements Sleep Mode
When the key is not in use, it will enter a sleep
mode in which the key cannot be accessed.
To wake the key and prepare it to accept key
inputs, press the UNLOCK key once.
The RED LED will glow solidly.
Battery Note
The Aegis Secure Key has an internal rechargeable battery with a smart-charging circuit and
will automatically charge whenever it’s plugged into a powered USB port. After initial Admin
PIN setup, when plugged into a powered USB port while in standby mode, the Red LED will
pulse to indicate that it’s charging and will glow solidly once fully charged. Since the Secure
Key ships with a partial charge, plug it into a powered USB port for 60-80 minutes to give the
battery a full charge before initial setup (RED LED will still be blinking.)
IMPORTANT:
Do NOT press any buttons while the
Secure Key is plugged into a USB
port. Doing so may cause damage
to the USB port and Secure Key
USB Connector.
Locking the Key
To lock the key, simply press the button. When locked, the RED LED will glow solidly.
If data is still being written to the Secure Key, it will wait for this operation to be completed before the
locking operation takes place. The button can also be used to exit out of the Admin mode.
Note: The Aegis Secure Key will not be recognized by any operating system in its locked state.
Unlocking the Key
1. Beginning in standby mode, press the button to wake the drive. (The RED LED will glow solidly.)
2. Enter either an Admin PIN or User PIN and press the button.
(If the PIN is accepted, the GREEN LED will quickly blink four times, then continue to blink
slowly until it’s plugged into a USB port, after which will then glow solidly;
If the PIN is incorrect, the RED LED will blink three times and then glow solidly.)
3. Upon correct PIN entry, the key will be unlocked and ready for use. If it is not plugged into a
USB port within 30 seconds, the key will return to sleep mode and automatically lock itself.
Adding a New User PIN
Performing a Complete Reset
Apricorn provides the following helpful resources:
1. Apricorn’s Website (http://www.apricorn.com)
2. E-mail us at support@apricorn.com
3. Call Technical Support at 1-800-458-5448 from
8:00 a.m. to 5:00 p.m. PST, M - F
Technical Support
1. Beginning in standby mode, press the button to wake the drive. (The RED LED will glow solidly.)
2. Enter the Admin Mode by pressing and holding + 0 for ve seconds (RED LED will blink.)
3. Enter the Admin PIN and press (BLUE LED will glow solidly.)
4. Press and hold + 1 until the BLUE LED glows solidly and the GREEN LED starts blinking.
5. Enter the PIN to be used as your User code and press . (BLUE LED will turn off and GREEN LED
will blink 3 times by itself, then will continue blinking as BLUE LED resumes glowing solidly)
6. Quickly re-enter that same PIN once more and press
(If the PIN was successfully added, BLUE LED will turn off, GREEN LED will illuminate for a second
or two and then will turn off, followed by the BLUE LED glowing solidly indicating that the key has
returned to Admin Mode. If PIN is unacceptable or the second entry doesn’t match the rst, RED
LED will ash three times, followed by solid BLUE / Blinking GREEN LEDs--Return to step 5 to retry.)
WARNING: BACK UP ALL IMPORTANT DATA PRIOR TO RESETTING THE SECURE KEY. PERFORMING A
RESET WILL ERASE ALL DATA AND DISK FORMATTING. AFTER A RESET, THE SECURE KEY WILL NEED
A NEW ADMIN PIN SETUP AND WILL ALSO NEED TO BE INITIALIZED / REFORMATTED PRIOR TO USE.
FOR REFORMATTING INSTRUCTIONS, REFER TO THE SECURE KEY 3.0 USER’S MANUAL ONLINE.
To perform a complete reset of the key, do the following:
1. Press + + 2 together and hold as RED and BLUE LEDs blink alternately.
2. Continue to hold until blinking stops and either the RED or BLUE LED glows solidly,
then release all keys.
3. Reset is complete and the key will need a new Admin PIN.
(BLUE and GREEN LED will glow solidly.)
Formatting / Reformatting the Key
The Aegis Secure Key comes
preformatted in NTFS for
Windows
®
and is ready for use.
For the Mac OS, use Apple’s
Disk Utility to reformat the drive
to a Mac compatible le system.
Complete formatting instructions
can be found online at
www.apricorn.com/media/
uploads/ASK3_Manual.pdf
(Rev 1.8) 6/13/2016
Need help?
General
