AEO WP401209 - User Manual

Section 1: INCLUDED
(1) Water Pump (2) Nozzles (3) DC Short Connector
Section 2: CAUTIONS
1) Make sure the water pump is fully submerged underwater while it is
operating.
2) Do not connect the pump to any AC power supply; it is designed
ONLY for DC power between 12V to 24V. When connects to a Solar
Panel, an 18V Solar Panel is recommended, because a 24V solar panel
actual output will exceed its nominal voltage when sunlight at highest
intensity.
3) The polarity of the power
cable plug on the Water
Pump (1) must match the
plug on the DC Short
Connector (3) as shown in
the figure to the right.
Connect the two plugs by
matching the flat sides; do
not force them together.
4) Any alteration of the product itself or changing of the components
voids warranty.
5) Operate the pump in water only (under 104°F), and keep it away from
flammable liquids.
Section 3: ASSEMBLY
*Unpack all components carefully.
1) [Setup Water Pump]
a) Connect the nozzles tubes (adjust the height by the number of
tubes) to the water pump outlet to produce a fountain effect
above the surface of the water. Use a taller base such as bricks or
marble slabs if the cylinder is not high enough.
b) Connect one of the fountain heads on top of cylinder tubes for
different water patterns.
c) Place the water pump under the water (fish tank, small pond, etc.),
but on top of a base such as a brick or marble slab to prevent dirt,
mud, or sand from getting into the filter. For deep water, the AEO
Floating Pad is recommended and can be found on Amazon.com
by searching for “AEO Floating Pad”.
2) [Connect the Water Pump to DC Short Connector] connecting the
plugs between the power cable and DC Short Connector (3). The plugs
must match in polarity (+ -). Connect the two plugs by matching the
flat sides. (See figure in Section 2-3)
AEO-WP401209 SOLAR DC WATER PUMP
USER’S MANUAL
Brushless Submersible, 12V-24V, 196GpH
for Solar Fountain, Hydroponics and Aquaponics
 Place the Water Pump under water BEFORE connecting to a power source.
 The water pump may become damaged if it is not under water before
powering it on.
 The plugs on the DC Short Connector (3) and power cable connected to the
Water Pump (1) must match in polarity (+ -). Connect the two plugs by
matching the flat sides. (See figure in Section 2.3)
 This is a DC (Direct Current) water pump. DO NOT connect to any AC power.
 Water Pump can be powered by a 12V-24V DC battery; however, when
connects to a Solar Panel, an 18V Solar Panel is recommended, because a
24V solar panel actual output will exceed its nominal voltage when sunlight
at highest intensity.
 Please carefully read this user manual before installing the pump.


Summary

Cautions and Safety Warnings

Ensure Pump is Submerged

Ensure the water pump is fully submerged underwater during operation to prevent damage.

Use DC Power Only

Connect the pump only to DC power sources between 12V and 24V, not AC power.

Polarity and Connector Matching

Match the polarity (+/-) and flat sides of plugs for the DC Short Connector and power cable; do not force.

Warranty Voiding Conditions

Product alteration or component changes will void the warranty.

Operating Environment and Safety

Operate pump in water (under 104°F) and away from flammable liquids.

Assembly Instructions

Water Pump Setup Procedure

Connect nozzles, adjust height, and place the pump on a base to prevent debris intake.

Connect Pump to DC Short Connector

Connect the power cable and DC Short Connector plugs, ensuring correct polarity and flat side matching.

Cleaning and Maintenance Procedures

Periodic Pump Cleaning

Clean the water pump periodically to prevent blockages and ensure optimal performance.

Cleaning Safety Precautions

Handle with care, disconnect power before cleaning, and prevent impeller damage.

Troubleshooting Common Issues

Troubleshooting: Pump Stopped Running

Check power source and ensure solar panel is clean and fully exposed to sunlight.

Troubleshooting: No Water Flow

Check nozzle tubes, pump outlet, and filter for any debris or blockages.

Technical Data and Pump Curve

Pump Performance Specifications

Details on operating voltage, maximum head, maximum flow rate, dimensions, weight, and cable length.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The AEO-WP401209 Solar DC Water Pump is a brushless submersible pump designed for use in solar fountains, hydroponics, and aquaponics. It operates on a DC power range of 12V to 24V, offering versatility in power sources.

Function Description:

This water pump is engineered to create fountain effects, circulate water in hydroponic systems, and maintain water flow in aquaponics. It is specifically designed for DC power, making it suitable for use with solar panels or DC batteries. The pump's submersible nature ensures quiet operation and efficient water movement.

Important Technical Specifications:

• Operating Voltage: DC 12V-24V
• Maximum Pump Head (Hmax):
  • 2.95 ft @ 12V
  • 7.85 ft @ 24V
• Maximum Flow Rate (Qmax):
  • 124 G/H @ 12V
  • 196 G/H @ 24V
• Dimensions: 4.17 x 1.85 x 1.97 inches
• Net Weight: 0.99 lbs.
• Cable Length: 16.4 ft
• Recommended Solar Panel: An 18V solar panel is recommended when connecting to a solar panel, as a 24V solar panel's actual output may exceed its nominal voltage at highest sunlight intensity.
• Operating Temperature: Operate in water only, under 104°F.

Usage Features:

• Submersible Operation: The pump must be fully submerged underwater while operating to prevent damage.
• DC Power Only: This is a DC (Direct Current) water pump and must NOT be connected to any AC power supply. It is designed ONLY for DC power between 12V to 24V.
• Polarity Matching: When connecting the power cable plug on the Water Pump to the DC Short Connector, ensure the polarity (+ -) matches by aligning the flat sides of the plugs. Do not force them together.
• Fountain Effects: The pump comes with nozzles and fountain heads to produce various water patterns. The height of the fountain can be adjusted by the number of tubes used.
• Placement: Place the water pump under the water (e.g., in a fish tank or small pond) but on top of a base like a brick or marble slab. This prevents dirt, mud, or sand from entering the filter. For deep water applications, the AEO Floating Pad is recommended.
• Easy Assembly: The pump includes a water pump unit, nozzles, and a DC short connector for straightforward setup.

Maintenance Features:

• Periodic Cleaning: The water pump should be cleaned periodically to prevent blockage and ensure optimal performance.
• Disassembly for Cleaning:
  1. Disconnect the pump from the power source before cleaning.
  2. Pull the filter housing apart from the pump by squeezing the sides.
  3. Press on the bottom board, sliding it in the direction of the arrow.
  4. Turn the impeller cover counter-clockwise and carefully pull it out. Be aware that the impeller may be attached to the cover or remain inside the pump, and white washers may fall out.
  5. Separate the impeller from the water pump or detach it from the impeller cover.
  6. Wash every part, including the inside of the motor chamber, and clean out any debris.
  7. Assemble the pump in reverse sequence.
• Troubleshooting - Pump Stopped Running:
  • Check Power Source: If connected to a solar panel, ensure it is fully exposed to sunlight and not covered in shade or dirt, as shadows or dirt on one cell can significantly compromise power output.
  • Check for Blockage: Clean the pump as described in the maintenance section.
• Troubleshooting - Pump Running, No Water Flow:
  • Check for Blockage: Clean the nozzle tubes, water pump outlet, and filter to remove any debris.
• Warranty: Any alteration of the product itself or changing of its components voids the warranty.
• Customer Support: For defective or damaged products upon delivery, customer service can be contacted via email at support@aeoselect.com or by phone at 909-698-8199.

AEO WP401209 Specifications