Diagram
Micro Double Switch G2
1. Remove the two screws securing the cover plate.
While the Micro Double Smart Energy Switch G2 is powered in
a 3-wire system, each external switch/button can be toggled to
initiate pairing into the Z-Wave network. Or the internal button
can be pushed to initiate pairing into the Z-Wave network if the
Micro Double Smart Energy Switch G2 was not put into in-wall
box.
While the Micro Double Smart Energy Switch G2 is powered in
a 3-wire system, each external switch/button can be toggled 10
times in quick succession to initiate removing from the Z-Wave
network. Or the internal button can be pushed to initiate pairing
into the Z-Wave network if Micro Double Smart Energy Switch
G2 was not put into in-wall box.
Note
: If the Micro Double Smart Energy Switch G2 was not put into an
in-wall box, another way to reset Aeotec Micro Double Smart Energy
Switch G2 is to press and hold the button which is on Micro Double
Smart Energy Switch G2 for 20 seconds.
1
23
AC PowerLoad
Neutral
NLL1
L2
L
N
L
N
Micro Double Smart Energy Switch G2
(Generation 2)
(In-Wall Z-Wave Appliance Module w/ Energy Monitor)
Introduction:
IMPORTANT:
The Aeotec Micro Double Smart Energy Switch G2 is
a
low-cost Z-Wave appliance module specifically
used
to enable Z-Wave command and control (on/
off) of existing in-wall switches. It can control 2 loads
independently. It can also report
immediate wattage
consumption or kWh energy
usage over a period
of time.
The wireless module is powered from the mains
supply and is a three-wire design which requires
a neutral connection. In the event of power
failure, non-volatile memory retains all
programmed information relating to the units
operating status.
It also is a repeater in the Z-Wave network.
Acting as a bridge for communication, it will
forward Z-Wave command messages to their
destinations if the originating controller is out of
range from the destination node.
By taking advantage of the Z-Wave mesh
network, commands can be routed to their
destination via intermediary “listening” Z-Wave
products. Products that are Z-Wave certified can
be used and communicate with other Z-Wave
certified devices.
A licensed electrician with knowledge and
understanding of electrical systems and electrical
safety should complete the electrical installation
inside the main circuit box (usually located outside of
your house).
Z-Wave Network Instructions:
The Aeotec Micro Double Smart Energy Switch G2 must be
paired
(included) into a Z-Wave network before it can receive
Z-Wave commands to turn on/off and report its energy usage.
The Micro Double Smart Energy Switch G2 can only
communicate to
devices within it’s own Z-Wave network.
Note:
The LED on the Micro Double Smart Energy Switch
G2 will
blink if it is currently not paired into a Z-Wave network.
In-Wall Electrical Installation Instructions:
Step 1
Dismounting In Wall Box.
Step 2
Step 3
IMPORTANT: The electricity to the circuit must be shut off
during installation for safety and to ensure that wires are not
short circuited during installation thus causing damage to
the Micro Module.
Preparing and Connecting Wires
The Aeotec Micro Double Smart Energy Switch G2 must first be
powered
by a 3-wire system in order to operate. The wiring
diagram
is
as follows:
Step 4
Mounting In Wall Box.
Step 5
Restore Power
2. Remove the wall switch cover plate.
3. Remove the two screws securing the wall switch to the wall
box. Disconnect both wires from the wall switch.
1. Position all wires to provide room for the device. Place Micro Double
Smart Energy Switch G2 inside the wall box towards the back of the box.
2. Position the antenna towards the back of the box, away from all other
wiring.
3. Reinstall the wall switch to the wall box.
4. Reinstall the cover plate onto the wall box.
Restore power at the circuit breaker or fuse.
Installation is complete.
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
Cut wire if
neccessary
Strip Gage
(measure bare
here)
0.27”
(7mm)
Adding/Including/Pairing the Micro Double Smart
Energy Switch G2 into a Z-Wave Network
Note:
To include the Aeotec Micro Double Smart Energy Switch
G2 with other controllers, please consult the operation manual
for these controllers on how to include Z-Wave products
into an existing network.
Include
Associate
Learn
Remove
1
Press the button labeled “Include” on
the Aeotec Minimote to begin the
Z-Wave inclusion process.
2
Troubleshooting:
If the Aeotec Micro Double Smart Energy Switch G2
was
not
successfully included into any Z-Wave network, the LED will
blink continuously
slowly continually. If the Aeotec Micro Double Smart Energy
Switch
G2 was
successfully included to a Z-Wave network, the Status
Indication LED will either be solid on or off (depending on if the switch
is on or off) .
Include
Removing/Resetting the Micro Double Smart Energy
Switch G2 from your Z-Wave Network
Include
Associate
Learn
Remove
1
Press the button labeled “Remove” on
the Aeotec Minimote to begin the Z-Wave
removal process.
Remove
Note:
To remove the Aeotec Double Micro Smart Energy Switch
G2
from other controllers, please consult the operation
manual for these controllers on how to remove Z-Wave
products from an existing network.
2
Troubleshooting:
If the Aeotec Micro Double Smart Energy Switch G2 was
removed from the Z-Wave network, the Status Indication LED will be
blinking. If the Aeotec Micro Double Smart Energy Switch G2 was not
successfully removed from the Z-Wave network, the Status Indication
LED will either be solid on or off (depending on if the switch is on or off).
1. Live / hot wire (Black wire). Connect to Live terminal of Micro Double Smart Energy
Switch G2.
2. Neutral (White wire). Note: If this wire is not present in the box, a neutral wire must
be pulled into the box.
3. Load wire. Connect to Load terminal of Micro Double Smart Energy Switch G2.
4. Signal connection: Using three
18 AWG copper wires, connect
the terminals of the wall switch
to Micro Double Smart Energy
Switch G2 as shown.
5. Side wire connection
1
2
3
Make sure that the ends of the wires from the
wall box are straight (cut if neccessary).
Remove insulation from each wire and the wall
box as shown.
Note: The "3V Out" terminal should be used only with the Aeon
Micro Touch.
To Next Page
Need help?
General