Aerohive AP1130 - User Manual

P/N 330120-02, Rev. A 1
®
AP1130 Installation Guide
The AP1130 is a multi-channel wireless access point with a watertight chassis that can be
deployed in virtually any outdoor setting, including extreme environments.
This guide explains how to install the AP1130 on a pole or flat surface in virtually any
outdoor setting, and connect it to Aerohive HiveManager Network Management over the
network. To register, get the latest product documentation, see compliance information, and
download software updates, visit
www.aerohive.com/support. For detailed hardware
information about this device, visit
www.aerohive.com/quick.
FCC and IC statements can be found on page 12.
Kit Contents, Required Accessories, and Tools
The AP1130 kit includes the items shown below.
To install your AP1130, you will need the following accessories (ordered separately) and tools:
• Two 2.4 GHz antennas
• Two 5 GHz antennas
• A switch that provides PoE power, or a PoE provisioning device, a DC backup battery (requires the
DC power cable accessory, part number AH-ACC-1130-CBL-DC), or solar panel
• A shielded cat5 Ethernet cable rated for outdoor use; length not to exceed 328 feet (100 m)
• PoE Injector (optional).
• Crosshead screwdriver for pan head screws and Reset button cover
• Flat blade screwdriver to tighten the hose clamp
• Security Torx (pin-in-Torx) screwdriver for the captive screws in the mounting bracket
Bracket (1)
AP1130
chassis
Five pan head machine
screws with washers for
pole mount and ground in
bag labelled “POLE MOUNT &
GROUNDING”
Four pan head wall
mount screws in the bag
labeled “WALL MOUNT”
Hose clamp
Ground cable (1)
Waterproof
Ethernet housing

Summary

Hardware Overview and Safety

Safety Instructions and Site Hazard Warnings

Details safety instructions and site hazard warnings, explaining icons used to convey caution and electrical hazards.

AP1130 Installation Procedures

Mounting the AP1130

Important Waterproof Cautions

Highlights critical precautions for maintaining the AP1130's waterproof seal, especially concerning antenna and cable connections.

Power Connections

Vertical or Horizontal Pole Mount

Provides step-by-step instructions for mounting the AP1130 onto poles using the bracket and hose strap.

Flat Surface Installation

Details the process of mounting the AP1130 onto a flat surface or wall using a bracket and appropriate wall anchors.

Attaching External Antennas

Configuration and Cable Management

Attaching the Ethernet Cable Waterproof Housing

Provides detailed steps to assemble and attach the waterproof housing for the Ethernet cable connection.

Network Connectivity and Protection

PoE and Ethernet Protection

Connecting to the Network

HiveManager Connection Process

Connecting to HiveManager

Details the AP's process of connecting to HiveManager via DHCP, DNS, and CAPWAP, including troubleshooting steps.

Regulatory Compliance and Information Resources

Federal Communication Commission Interference Statement

Industry Canada (IC) Statement

Aerohive AP1130 Specifications

Operating Environment

operating temperature	-40° to 140° F (-40° to 60° C)
storage temperature	-40° to 176° F (-40° to 80° C)
wind survivability	165 mph (266 kph)
environmental compliance	IP67

Power and Connectivity

maximum power	20 Watts
ethernet connector	autosensing 10/100/1000 Base-T Mbps
PoE standard	IEEE 802.3at

Antenna Specifications

frequency range	5150-5850 MHz
bandwidth	700 MHz
gain	18 dBi
polarization	vertical/horizontal

Weight and Dimensions

width	10" (254 mm)
height	10" (254 mm)
depth without bracket	1.625" (42 mm)
depth with bracket	8.75" (222 mm)
weight	2.54 lb (1.15 Kg)
mounting mast diameter	1.5" - 2" (40 - 50 mm)