Aeropro ST64X - User Manual

Air Nailer –Concrete nailer
Model No.:ST64X
Residual risks
Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following
hazards may arise in connection with the tool’s construction and design:
 Damage to lungs if an effective dust mask is not worn.
 Damage to hearing if effective hearing protection is not worn.
 Health defects resulting from vibration emission if the power
tool is being used over longer period of time or not adequately
managed and properly maintained.
 Wear eye protectio
n.
Content
1 Technical data 2.7 Actuating systems
1.1 Fastener 3 Compressed air system
1.2 Accessories 4 Preparing the tool for use
1.3 Description/Features 4.1 Preparing a tool for first operation
1.4 Location of Parts 4.2 Connection to the Compressed air system
2 Special references 4.3 Filling the magazine
2.
1 Regulations 4.4 Handling the tool
2.2 Noise emission 5. Maintenance
2.3 information on mechanical impact (vibration) 6 Troubleshooting
2.4 Safety of fastener driving tool 7 explode drawing
2.5 Safety at work 8 Spare parts list
2.6 Triggering devices
2018
OPERATING INSTRUCTIONS FOR FASTENER DRIVING TOOLS
OPERATED BY COMPRESSED AIR
IMPORTANT:
Read all safety rules and operating
Instructions carefully before first use it.
Keep this Manual for future reference.

Summary

Technical Data and Specifications

Fastener Specifications

Details on fastener type, size, and magazine capacity for the nailer.

Tool Accessories

Lists included accessories such as Hexagon Key, Lubricant, and Operating instruction.

Description and Features

Overview of the T-nailer's capabilities, construction, and application for wood to concrete steel.

Location of Parts

Identifies key components of the nailer, including Magazine, Trigger, Exhaust Vent, and Air Quick Coupler.

Special References and Safety Guidelines

Applicable Standards and Instructions

Details EN792-13:2000+A1:2008 standard and requirements for fasteners, couplings, and energy sources.

Noise Emission Information

Describes characteristic noise values determined by EN12549:1999 and ISO4871 standards.

Mechanical Impact (Vibration) Data

Provides vibration values according to ISO 8662-11:1999 and EN 12096 for hand-held power tools.

Fastener Driving Tool Safety

Covers pre-operation checks, restrictions on modifications, and proper servicing procedures.

Workplace Safety Precautions

Emphasizes not pointing the tool at others, maintaining control, and avoiding damage to the tool.

Triggering Devices and Actuating Systems

Explains operation via trigger and safety yoke, detailing single sequential and contact actuation.

Compressed Air System Requirements

Preparing and Using the Tool

First-Time Operation Preparation

Advises reading instructions and following basic safety measures before initial use.

Connecting to Compressed Air

Instructions on setting pressure, ensuring proper connections, and using quick-action connectors.

Filling the Magazine

Guidance on using specified fasteners and safe magazine loading procedures.

Handling the Tool Safely

Tips on proper tool operation, air pressure adjustment, and avoiding accidental firing.

Maintenance Procedures

Troubleshooting Common Issues

Exploded View and Spare Parts List

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

This document describes the ST64X Air Nailer (Concrete Nailer), a fastener driving tool operated by compressed air, designed for both wood and concrete/steel applications.

Function Description

The ST64X is a T-nailer specifically engineered for driving 14 gauge T-nails, ranging from 18mm (3/4") to 64mm (2-1/2") in length, into various materials including wood, concrete, and steel. Its primary function is to provide efficient and powerful fastening for construction and similar tasks. The tool features a lightweight die-cast housing to minimize operator fatigue, enhancing productivity during extended use. It operates using compressed air, requiring a specific pressure range for optimal performance.

The tool incorporates a safety yoke mechanism, which ensures that driving operations can only be carried out when the muzzle is pressed against a workpiece. This prevents accidental firing into free space, reducing the risk of injury from free-flying fasteners and excessive strain on the tool. Depending on its purpose, the ST64X can be fitted with either a single sequential actuation system or a contact actuation system.

• Single sequential actuation: Requires both the trigger and safety yoke to be activated. Only one driving operation occurs per trigger pull after the muzzle is applied to the driving location. Subsequent operations require the trigger to be released and re-pulled while the safety yoke remains depressed.
• Contact actuation (restricted version): Allows for repeated driving operations as long as either the trigger or the safety yoke remains activated. The order of actuation is not specified. This mode is typically used for rapid fastening but comes with specific safety warnings, particularly regarding use on scaffolds or ladders. Tools with contact actuation are marked with a symbol indicating they should not be used on scaffoldings or ladders.

Important Technical Specifications

• Model No.: ST64X
• Type of tool: T-nailer
• Outline dimension: 90mm x 275mm x 355mm
• Weight (without fasteners): 3.3 kg (7.27 lbs)
• Required pressure: 5.5-8 Bar (80-110 Psi)
• Max. pressure: 8.3 Bar (120 Psi)
• Recommended lubricant: White mineral oil 10 #
• Fastener size: Ga14 (2.2)
• Nail length: 18-64mm (3/4"-2-1/2")
• Magazine capacity: 70 pieces
• Accessories: Hexagon Key, Lubricant, Operating Instruction

The compressed air system requires careful setup. The maximum allowable pressure of the tool must not be exceeded by more than 10%. If the supply pressure is higher, a pressure reducing valve with a downstream safety valve must be integrated into the air supply. The system should include filtered, dry, and lubricated compressed air. Water separators are crucial to remove condensate from the air, preventing corrosion in the system and tool. Connecting points should be fitted with a compressed air servicing unit (filter/water separator/oiler) directly at the junction point.

Usage Features

• Ease of Use: The lightweight design minimizes operator fatigue, making it suitable for prolonged use.
• Versatility: Capable of driving nails into wood, concrete, and steel, making it adaptable for various construction and fastening tasks.
• Safety Mechanisms: Equipped with a safety yoke that prevents accidental firing, enhancing user safety. The tool also features different actuation systems (single sequential and contact) to suit specific application needs and safety requirements.
• Adjustable Air Pressure: The air pressure can be adjusted to control the depth of fastener penetration. If fasteners protrude, increase pressure in 0.5 bar increments; if driven too deep, reduce pressure in 0.5 bar increments. The lowest possible air pressure is recommended for energy saving, noise reduction, and reduced tool wear.
• Quick-Action Couplings: The tool should be connected to the compressed air system using quick-action couplings, ensuring no compressed air remains in the tool after disconnection.
• Prohibition of Oxygen/Combustible Gases: Oxygen or combustible gases must not be used as an energy source for compressed air operated fastener driving tools.
• Workpiece Contact: The muzzle of the tool must be pressed against the workpiece for operation, preventing free-firing.
• Handling: Always carry the tool by its handle, never by the trigger, especially when moving or using ladders.

Maintenance Features

• Regular Lubrication: If not using an in-line automatic oiler, 2 to 6 drops of pneumatic tool oil should be placed into the air inlet before each workday or after 2 hours of continuous use, depending on the workload.
• Periodic Inspection: Air-operated tools require periodic inspection. Worn or broken parts, such as O-rings and seals, must be replaced to maintain safe and efficient operation. All screws and caps should be tightened.
• Safety Mechanism Check: Regular inspection of the trigger, spring, and safety mechanism is essential to ensure they are complete and functional, with no loose or missing parts.
• Cleanliness: The magazine and nose of the tool must be kept clean and free of dirt, lint, or abrasive particles to prevent jams and ensure smooth operation.
• Storage: When temperatures are below freezing, the tool should be kept warm using a convenient and safe method.
• Disconnection: Always disconnect the tool from the compressor before adjusting, clearing jams, servicing, relocating, or during non-operation.
• Professional Repair: Repairs should only be carried out by manufacturer-authorized agents or experts using specified spare parts. Unauthorized modifications are prohibited.
• Air System Maintenance: Water separators in the compressed air system must be checked daily and drained if necessary to prevent corrosion. The compressed air connectors and hoses should be protected from contamination.
• Troubleshooting Guide: The manual includes a troubleshooting table to address common issues such as air leaks, inadequate fastener driving, skipped fasteners, and tool jams, providing corresponding solutions.

Aeropro ST64X Specifications

General

Brand	Aeropro
Model	ST64X
Category	Nail Gun
Language	English