AFG 2.0 AS - Assembly Step 2: Pulley Assemblies and Seat Components; Assembly Step 3: Radial Arm and Connection Tubes

iI_ ii_i i
_ i i i I
H
il__iii_i_i_i!I_ii_ii_!!_i_
i ii
i / _ii
2.0 AS rev 1.2.indd 8-9
_ YLON
NUT(E)
Qty:4
BOLT(B) _ ARCWASHER(D)
95 mm _ Qty:12
Qty:4
BOLT(F) _ LARGE"O"RING
_25mm Qty:l
V)
Qty:4
ARCWASHER(D)
CENTER
SUPPORTFRAME
SEAT
WELDMENTSET \
\
ARCWASHER(D)
NYLON NUT(E)
UPPER PULLEY
ASSEMBLY
ARCWASHER(D)
(A)
......_. LEFTSUPPORT
FRAME
RIGHT
SUPPORT
/FRAME
SEAT
ADJUSTMENT/
PIN
t
SEATSAFETYPiN
A
B
C
D
E
F
G
OpenHARDWAREBAGZ
Slide LARGE"0" RING
onto CENTERSUPPORT
FRAMEas shown in
diagram.
AttachUPPERPULLEY
ASSEMBLYtoCENTER
SUPPORTFRAMEusing
4 BOLTS(F) and 4 ARC
WASHERS(D). Tighten
this hardware.
Attach UPPERPULLEY
ASSEMBLYto RIGHT
MAINSUPPORTFRAME
using2 BOLTS(B), 4
ARC WASHERS(D)and 2
NYLONNUTS(E).
AttachUPPERPULLEY
ASSEMBLYtoLEFT
SUPPORTFRAMEusing
2 BOLTS(B),4 ARC
WASHERS(D),and 2
NYLONNUTS(E).
Install SEATWELDMENT
SETonto posts on
CENTERSUPPORTFRAME
as shown in diagram, and
insert SEATSAFETYPIN.
Install SEATAD]USTMENT
PINintoSEATWELDMENT
SETas shownin
diagram.(Fullythread
into SEATWELDMENT
SETafter SEATBOTTOM
AD]USTMENTBARis
installed.)
(_ FLAT
WASHER(C)
Qty:10
BOLT(H)
20 mm
Qty:4
NYLON BOLT(F)
NUT(E)_ 25 mm
Qty:2 Qty:2
(_ FLAT
WASHER(I)
Qty:2
BOLT(G)_ NYLON
92mm _NUT(K)
Qty:l Qty:1
BOLT(J) _ LOCK
83 rnrn _ WASHER(L)
Qty:2 Qty:2
RADIALARMASSEMBLY
CENTER
SUPPORT-_
FRAME
FLATWASHER
NYLONNUT(E)
NYLONNUT(K)\
NYLONNUT(E)\o.
CENTER
CONNECTION
TUBE
LEFT
CONNECTION
--/ TUBE
BOLT(J) BOLT(J)
LEGROLLER_ BOLT(G)
SUPPORTTUBE FLATWASHER(1)
FLAT
LOCK
WASHER(C)WASHER(L)
RADIALARM
ASSEMBLY
(c)
(H)
"-_..
RIGHTCONNECTIONTUBE
LOWER
CONNECTIONTUBE
A OpenHARDWAREBAG3.
B RemoveSTOPPERfromfrontsideof RADIALARMASSEMBLYand reinstaflon backside.
TightenbothSTOPPERS.
C AttachRADIALARMASSEMBLYto CENTERSUPPORTFRAMEusing2 BOLTS(F),2 LOCK
WASHERS(L)and2 FLATWASHERS(C). Tightenthis hardware.
D AttachRIGHTSIDECONNECTIONTUBEtoSEATWELDMENTSETand toLOWER
CONNECTIONTUBEusing2 BOLTS(H)and 2 FLATWASHERS(C),as shownin diagram.
E Repeatonleft side.
F AttachCENTERCONNECTIONTUBEtoSEATWELDMENTSETand toLOWERCONNECTION
TUBEusing2 BOLTS(1),4 FLATWASHERS(C)and 2 NYLONNUTS(E).
G AttachLEGROLLERSUPPORTTUBEto LOWERCONNECTIONTUBEusing 1 BOLT(G),2
FLATWASHERS(I) and 1NYLONNUT(K).Tightenall hardwarein Step3.
/
i(i /
12/28/07 10:15:56 AM