_ i i i I
W
il__iiii_ii!I_ii_ii_!!_i_
i ii
i / _ii
2.0 AS rev 1.2.indd 6-7
UPPERPULLEYASSEMBLY
DUALFLOATINGPULLEYBRACKET
LATPULLDBWNBAR
LARGE"O" RING
CENTERSUPPORTFRAME
WATERBOTTLEHOLDER
CABLE"B"
SEATHEADPAD
HANDLES
RADIALARMADJUSTMENTPiN
SEATBACKPAD
SEATBACKADJUSTMENTKNOB
BICEPCURLBAR
SEATBOTTOMPAD
WEIGHTSHROUD
CABLE"C"
GUIDEROD
RADIALARMASSEMBLY
ACCENTPIECE
BAYONET
WEIGHTSELECTIONPiN
RIGHTSUPPORTFRAME
-- SINGLEFLOATINGPULLEYBRACKET
-SEATASSEMBLYSAFETYPiN
SEATWELDMENT
LEGEXTENSION/CURLDOWNTUBE
ADJUSTMENTBAR
SEATHEIGHTADJUSTMENTKNOB
FOAMROLLERS BASEFRAME
ADJUSTABLEFOOTPLATE > CABLE"B"
roo sINg UDfD ....
i
[] 8rnrnFlatWrench [] 13rnrn/17rnrnFlatWrench [] 5rnrnAIlenWrench
[] 19 rnrn Flat Wrench [] 4 rnrn Allen Wrench [] 6 rnrn Allen Wrench
[] 1 Bayonet [] 1 Center Support Frame [] 2 Single Floating Pulley Bracket
[] 1 Bicep Cuff Bar [] 1 Seat Weldment [] 1 UpperPulleyAssernbly
[] 1 Seat Back Pad [] 2 Weight Shrouds [] 1 Seat Bottom Pad
[] 1 Base Frame [] 2 Guide Rods [] 1 NylonAnkle Strap
[] 1 Left Support Frame [] 1 Weight Selection Pin [] 2 Handles
[] 1 Right Support Frame [] 1 5 Ib, Increment Weight [] 1 Lat Pulldown Bar
[] 1 Seat Back Adjustrnent Bar [] 1Dual FIoating Pulley Bracket [] l Ol-lardware Bags
[] 1 Radial Arrn Assernbly [] 1 Set Of Weight Plate Decals [] 2 FoarnRollers
[] 1 Exercise Flipbook [] 1 Center Connection Tube [] 1 Seat Head Pad
[] 2 Seat Adjustment Pins [] 1 Lower Connection Tube [] 2 Side Connection Tubes
[] 1 Leg Roller Support Tube [] 1 Lower Pulley Bracket [] 1 Upper Mounting Bracket
[] 1 WaterBottle Holder [] 2 Upgrade Spacers [] 1 Lower Mounting Bracket
[] 1 Seat Bottom Adjustment Bar [] 2 Accent Pieces
Contactinforrnationis locatedon the backpanel of this manual.
Fora completeexplodeddiagram, visit usat www,advancedfitness ro_zoujzcorn
NOTE: Durin_ each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely ti_htenin_ any ONEbolt,
/VOTE:A light application of grease may aid in the installation of hardware, Any grease, such as lithium bike
grease is recommended,
BOLT(A) BOLT(B)
_ 75rnrn _ _ 95rnrn
Qty:2 Qty:4
FLATWASHER(C) _) ARCWASHER(D) (_NYLON
Qty:4 Qty:8 NUT(E)
Qty:6
LEFTSUPPORTFRAME
CENTER
SUPPORTFRAME
BASEFRAME
i
ARCWASHER(D)
NYLONNUT(E)
i i
@
' *--- LOWERPULLEYBRACKET
t ÷_ FLATWASHER(C)
° _ NYLONNUT(E)
A
B
C
D
E
Place BASEFRAME
on floor in desired
location.
OpenHARDWAREBAG
1.
AttachRIGHT
SUPPORTFRAMEto
right side of BASE
FRAMEusin_2 BOLTS
(B),4 ARCWASHERS
(D)and 2 NYLONNUTS
(E).
AttachLEFTSUPPORT
FRAMEtoleft sideof
BASEFRAMEusin_
2 BOLTS(B),4 ARC
WASHERS(D)and2
NYLONNUTS(E).
AttachCENTER
SUPPORTFRAME
andLOWERPULLEY
BRACKETto BASE
FRAMEusin_2 BOLTS
(A),4 FLATWASHERS
(C)and 2 NYLONNUTS
(E).
NOTE:Ensurethat
theLOWERPULLEY
BRACKETis positioned
as shown in dia_rarn.
ii i iiii
/
12/28/07 10:15:50 AM
To Next Page
Loading...