What to do if the "Sludge alarm act." alarm appears on AFRISO OSA 3 Measuring Instruments?
If the "Sludge alarm act." alarm appears, it means the sludge level has reached a set alarm level. In this case, separator emptying should be ordered.
What to do if "High level alarm act." alarm appears in AFRISO OSA 3 Measuring Instruments?
If the "High level alarm act." alarm appears, there may be a blockage at the outlet to the separator. Clear the blockage or find out what is causing it.
What to do if "Sensor err on input 1 (level)" alarm appears in AFRISO OSA 3 Measuring Instruments?
If the "Sensor err on input 1 (level)" alarm appears, there may be an error in the sensor circuit to the sensor, such as a cable failure or short-circuit. To resolve this, measure the voltage at the sensor.
What to do if "Sensor err on input 2 (high level)" alarm appears in AFRISO OSA 3?
If the "Sensor err on input 2 (high level)" alarm appears, there may be an error in the sensor circuit to the sensor, such as a cable failure or short-circuit. To resolve this, measure the voltage at the sensor.
What to do if "Sensor err on input 3 (sludge)" alarm appears in AFRISO OSA 3 Measuring Instruments?
If the "Sensor err on input 3 (sludge)" alarm appears, there may be an error in the sensor circuit to the sensor, such as a cable failure or short-circuit. To resolve this, measure the voltage at the sensor.
What to do if "Level alarm act." alarm appears in AFRISO Measuring Instruments?
If the "Level alarm act." alarm appears, you should order emptying.
What to do if the sensor is not connected or there is a cable failure in AFRISO Measuring Instruments?
If the sensor is not connected or there is a cable failure, connect the sensor or troubleshoot the cable.
What to do if the sensor is connected incorrectly in AFRISO OSA 3 Measuring Instruments?
If the sensor is connected incorrectly, check the polarisation.
What to do if the sensor circuit is short-circuited in AFRISO OSA 3?
If the sensor circuit is short-circuited, check the sensor circuit.
Essential checks for commencing the electrical installation of the OSA 3 unit.
Final checks for correct installation and connection of the OSA 3 unit after setup.
Details wiring procedures for multi-core cables for the OSA 3 system.
Explains the function of terminals K1, K2, K3, K4 on the OSA 3 central unit.
Outlines procedures for wiring the OSA 3 using individual cables and junction boxes.
Provides specific guidance on fitting level, damming, and sludge sensors for optimal performance.
Covers initial operation, button functions, automatic setup, and setting date/time for the OSA 3.
Details the procedure for scanning and testing sensors to ensure proper function.
Explains how to test the damming (R6-S) and sludge (ES8) sensors.
Explains the display status during normal operation (STATUS OK).
Details how different alarms are indicated and the recommended actions.
Covers periodic cleaning of sensors and testing requirements as per standards.
Details access and use of programming functions like Date/Time, Inputs, Relay settings, and Language.
Provides a guide to common alarm messages, their checks, and potential causes/actions.
Explains sensor voltage measurements and provides a table for checking sensor status and actions.
Lists technical specifications for the OSA 3 central unit and its sensors.
Provides definitions for key terms used in the manual.
General| Service life of the battery | Up to 10 years |
|---|---|
| Housing | Plastic |
| Colour | White |
| Power supply | 3 V lithium battery |
| Alarm volume | 85 dB (A) at a distance of 3 m |
| Operating temperature | 0 °C...+55 °C |
| Storage temperature | -20 °C...+60 °C |
| Air humidity | 15 to 95 % RH (non-condensing) |
| Diameter | 100 mm |
| Approvals | EN 14604 |
To Next Page
