AGCO FENDT 1038 Vario S4 User Manual

Operator's Manual
Maintenance
1000 Vario
FENDT 1038 Vario S4
FENDT 1042 Vario S4
FENDT 1046 Vario S4
FENDT 1050 Vario S4
Marktoberdorf
AGCO GmbH - Johann-Georg-Fendt-Str. 4 - D-87616
Marktoberdorf
FENDT is a worldwide brand of AGCO
© AGCO 2015
Original Operator's Manual
November 2015
530.020.020.011 Rev.A
4879
EAME
English

AGCO FENDT 1038 Vario S4 Specifications

General

Rated Engine Power	279 kW / 380 hp
Transmission	Vario continuously variable transmission
Hydraulic System	Load sensing system
Fuel Tank Capacity	600 L
PTO Speed	1000 rpm

Summary

1 SAFETY INSTRUCTIONS

1.1.1 Safety advice in the instructions and on the vehicle

Provides essential safety advice for operating the tractor and implements.

1.3 Special safety instructions for tractor maintenance

Outlines general safety guidelines and warnings applicable to all maintenance and repair work.

1.3.1 General maintenance instructions

Outlines general safety guidelines and warnings applicable to all maintenance and repair work.

1.3.3 Obligatory steps to be taken before leaving the tractor

Lists essential safety steps to follow before leaving the tractor unattended.

2. Service and maintenance

2.3 Engine

Covers essential engine maintenance tasks.

2.3.2 Check the engine oil level

Detailed steps for accurately checking the engine oil level using the dipstick.

2.3.4 Change the engine oil filter

Instructions for replacing the engine oil filter, emphasizing replacement during every oil change.

2.4 Fuel system

Procedures for maintaining the tractor's fuel system.

2.4.2.2 Drain water and dirt

Procedure for draining accumulated water and dirt from the fuel pre-filter to maintain fuel quality.

2.4.3 Bleeding air from the fuel system

Guides on how to remove air from the fuel system to ensure proper engine operation.

2.5.2 Remove and install the main cartridge

2.6 Cooling system

Maintenance procedures for the cooling system.

2.6.3 Re-fill with coolant

Steps for refilling the cooling system with the correct coolant mixture.

2.8.1 Change the the front axle differential oil

2.9 Transmission and axle drives

Maintenance tasks for the transmission and axle drives.

2.9.6 Change the pressure and suction filters

Guide on changing the pressure and suction filters for the transmission.

2.10 Hydraulic system

Procedures for maintaining the tractor's hydraulic system.

2.10.4 Change hydraulic system filter

Instructions for changing the hydraulic system filter, including draining oil and replacing the filter element.

2.18 Cleaning the tractor

2.18.2 Clean with the high-pressure cleaner

2.18.3 Cleaning the Varioterminal

3. Faults and remedy

3.1 Warning and fault messages

General explanation of how warning and fault messages are displayed and stored.

3.1.2 Warning messages

Lists specific warning messages and their corresponding remedies or actions.

3.3 Fault code tables

Comprehensive tables detailing various fault codes and their remedies.

3.3.1 Fault code 00.0.00 -

3.3.2 Fault code 01.1.00 -

3.3.3 Fault code 02.0.00 -

3.3.5 Fault code 04.1.00 -

3.3.7 Fault code 06.1.00 -

3.3.8 Fault code 08.1.00 -

3.3.9 Fault code 09.1.00 -

3.3.13 Fault code 0E.1.00 -

3.3.14 Fault code 0F.1.00 -

3.3.15 Fault code 10.1.00 -

3.3.16 Fault code 12.1.00 –

3.3.17 Fault code 15.1.00 -

3.3.18 Fault code 17.1.00 –

3.3.19 Fault code 18.1.00 -

3.3.20 Fault code 1D.1.00 -

3.3.22 Fault code 20.1.00 –

3.4 Emergency mode

Guidance on operating the tractor in emergency modes.

3.4.2 Transmission engaged

3.4.3 Transmission control unit faulty

3.4.6 Towing instructions

Important safety instructions and procedures for towing the tractor.

3.4.6.1 Mechanical neutral position using auxiliary lever

3.4.6.2 Towing

Critical warnings and procedures for safely towing the tractor, including after-towing steps.

5. Lubrication and maintenance plan

5.1 Lubrication chart

5.1.1 Lubrication points

5.2 Maintenance schedule

Comprehensive schedule of maintenance tasks based on technical service, regular intervals, and daily checks.

5.2.1 Maintenance schedule

Comprehensive schedule of maintenance tasks based on technical service, regular intervals, and daily checks.