This document describes a nebulizing aroma diffuser, a waterless essential oil diffuser that uses cold diffusion technology to convert essential oil into nano vapor (1-3 microns) without heat or water. This process preserves the molecular structure of the essential oils, maintaining their therapeutic properties for easier absorption. The device is designed to be compact, fitting into car cup holders, and is compatible with most essential oil bottles (5ml, 10ml, 15ml, 20ml). It can be used with sanitizing essential oils to improve odors and purify the air.
Cautions:
- Do not invert or tilt the device once the oil bottle is installed.
- Do not use with camphor tree oil.
- Do not attempt to disassemble the device.
- For quieter operation, ensure the unit is 3 feet away.
- Keep away from children and pets.
- Highly concentrated oils may reduce diffusing ability.
- For extended storage, keep the device and nozzle separate.
- Working Temperature: 4º−104°F / 0 – 40°C.
- Suggested room size: 300-500 sq. ft.
What's in the Box:
- Diffuser
- Nozzle
- Charging Cable (USB-C)
- Standard Oil Bottle (20ml)
- Spare Kit (15ml, 10ml, 5ml atomizers)
The display turns off after 30 seconds of inactivity; tap any button to wake it up.
- Power button: Press and hold for approximately 1 second to turn on/off.
- Nozzle: The component through which the mist is diffused.
- Battery indicator: Shows the current battery level.
- 3-Level Mist Control:
- Tap to set the mist level.
- Long press to turn on/off the ambient light.
- Ambient light indicator: Shows if the ambient light is on.
- Orange ambient light: An orange light feature.
- Timer settings:
- Options: 1/2/4/6 hours.
- Tap to choose the timer duration.
- The diffuser will turn off automatically when the set time is finished. Press and hold the power button to turn it on again.
Mist Level Explained:
- Level 1: 15 seconds of diffusing, followed by a 165-second pause.
- Level 2: 1 minute of diffusing, followed by a 2-minute pause.
- Level 3: 1 minute of diffusing, followed by a 1-minute pause.
- Ambient light on: Indicated on the display.
- Low battery alert: Indicated on the display.
Bottle Installation:
The device is compatible with 5ml, 10ml, 15ml, and 20ml bottles.
- Removal: Push from the top and lift your finger until a "tick" sound is heard, at which point the nozzle will stick out. Then, pull it out to change or install an essential oil bottle.
- Installation: Screw the essential oil bottle onto the nozzle. Then, push the nozzle into the device until a "tick" sound is heard. For proper installation, align the "▲" sign before pushing the nozzle.
Charging:
- Normal charging time is 3-5 hours. If the charging current is below 1A, it will take longer to fully charge.
- The device can be charged using a 5V adapter, PC/MAC USB port, or a USB interface in a vehicle. Ensure the use of safety-certified charging accessories.
- The battery indicator blinks green during charging and remains green once charging is complete.
- Battery life will decrease as charging cycles increase.
Specifications:
- Max. Oil Capacity: 20ml
- Input: DC-5V/1A
- Rated Power: 1.5W
- Size: 73*122mm
- Battery Capacity: 2000mAh
- Net Weight: 300g
FAQ:
- How to select the right essential oil? Use 100% pure essential oils. Resin and thick oils are not recommended. Camphor tree and eaglewood oils are prohibited.
- How to clean the nozzle and bottle when changing oils? Fill an empty bottle with 5ml of 99% ethyl/ethanol alcohol. Shake to rinse the inner surface, then empty it. Refill with another 5ml of ethyl/ethanol alcohol and run the device until the alcohol runs out.
- Why does the device stop running sometimes? Refer to the "Mist Level Explained" section. The device automatically optimizes atomizing/pausing based on the mist level setting.
- How long does it take to fully charge? Normally 3-5 hours.
Need help?
General
To Next Page