EasyManua.ls Logo

AIS PIXIE RP10 Series - User Manual

AIS PIXIE RP10 Series
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Universal Model
THIS MICRO CHLORINE GENERATOR
CREATES A TOTALLY REJUVENATING
SPA AND PLUNGE POOL EXPERIENCE.
INSTRUCTION MANUAL
This manual is for:
PIXIE RP10 MODELS
ERP10H (Euro model)
RP10TH (Universal model
with timer)
RP10QTH (With battery
backup)

Table of Contents

Questions and Answers

  • M
    Marcus HernandezAug 12, 2025
    What to do if the circuit breaker is tripping on my AIS PIXIE RP10?
    • A
      abushAug 12, 2025
      If the circuit breaker is tripping, it could be due to several reasons: 1. A mains power surge may be the cause. Set the machine to off and push the circuit breaker. 2. There could be a fault with shorted electrodes. Inspect the electrode visually, checking for foreign or conductive surfaces. If any are found, remove and clean the cell. Also, check that the electrode plates are not touching each other; if they are, replace the cell. 3. There may be a fault with the power supply.
  • S
    smithdustinAug 16, 2025
    Why is my AIS Portable Generator not generating enough chlorine?
    • B
      Brooke NguyenAug 16, 2025
      There are several reasons why your AIS Portable Generator might not be producing enough chlorine: 1. Chlorine production might be set too low. Adjust the control knob clockwise to increase production. 2. The generator may not be operating for a sufficient amount of time. Increase the operation running time. 3. The electrode could be calcified. Clean the electrode (refer to the maintenance section). 4. The water chemistry may be incorrect. Correct the water chemistry.
  • E
    Erika KingAug 19, 2025
    How to fix the low salinity light on my AIS PIXIE RP10 Portable Generator?
    • M
      Michelle OconnellAug 19, 2025
      If the low salinity light is on or flashing, it indicates a problem with the water salinity or the electrode. Here's what you can do: 1. Have the salinity level tested by a pool professional and increase it to 4000 ppm if necessary. 2. The electrode may be calcified. Clean the electrode (refer to the maintenance section). 3. The electrode might be faulty. Have the electrode tested and replace it if necessary.
  • D
    Deborah RochaAug 23, 2025
    What to do if Status Light (3) is flashing and the AIS PIXIE RP10 Portable Generator is beeping?
    • N
      Nicole SmithAug 23, 2025
      If Status Light (3) is flashing and the generator is beeping, it could be due to: 1. The pump is not running, the filtration is blocked, or there is an air lock. A large air bubble in the electrode housing can cause this alarm. Clean out the skimmer box, check for and clear any blockage, and re-prime the pump. 2. The electrode lead may not be properly plugged in. Check that the electrode lead plug is properly plugged onto the electrode.
  • R
    Ryan Mcclure Jr.Aug 27, 2025
    How do I resolve the high salinity light issue on my AIS Portable Generator?
    • L
      Lisa HuffAug 27, 2025
      If the high salinity light is on or flashing, consider the following: 1. The pool salinity might be too high. Have the salinity level tested by a pool professional and decrease it to 5,500 ppm if necessary. 2. The chlorine generator might be faulty.
  • P
    Pamela CrawfordAug 30, 2025
    Why are there no lights on my AIS Portable Generator and the pump isn't running?
    • J
      John AndrewsAug 30, 2025
      If there are no lights on the chlorine generator and the pump isn't running, it could be due to: 1. Lack of mains power. Unplug the chlorine generator from the power and test the power outlet with another known working appliance. 2. The time clock is in a designated off period, or the switch is moved to the OFF position. Switch to BYPASS to circumvent TIMER or OFF functions.
  • R
    Rachael GreenSep 3, 2025
    Why is only Status Light (3) on when the pump is running on my AIS PIXIE RP10 Portable Generator?
    • C
      calvin50Sep 3, 2025
      If Status Light (3) is on and the pump is running, but no other lights are on, it might be because the chlorine generator production is turned off. To resolve this, adjust the control knob clockwise to increase production.
  • D
    Darryl WilliamsSep 7, 2025
    What causes a white powdery material on the pool bottom when using my AIS Portable Generator?
    • E
      Eric MitchellSep 7, 2025
      The presence of a white powdery material on the pool bottom is often due to excessive water hardness. Test the water chemistry and adjust accordingly.

AIS PIXIE RP10 Series Specifications

General IconGeneral
Fuel TypeGasoline
Engine Type4-Stroke OHV
DC Output12V
Outlet Types12V DC
Warranty2 years