Akai S01

3.
Press
the
REC
key once
more
to
execute
saving.
The PROG.
NO./DATA
display
will
show
rapid
movement
during
saving.
As saving
is
completed,
the
saved
file
will
be shown
by
a number
in
the
PROG.
NO./DATA
display.
The
next
time
you load
this
data,
you specify
the
data file with
that
number.
For
this
reason we
recommend
you
to take
note
of the
data contents
and
the file
number.
To
continue from
this
point,
press
the
REC key
to
save other
data. If
you
want
to stop saving
here,
select
another
parameter
to
continue
editing
using
the cursor
keys,
or return
to
Play
mode
using
the
EDIT key.
The
saving
time
required
will vary
depending
on the size
of the file.
*
White
the disk
is
being
accessed
(the
disk drive
LED will
be
lit),
do not
turn
off
the
power
or
attempt
removing
the
disk from
the
disk
drive. This
will
damage
the
disk
as well
as the
disk
drive.
If
the
disk in
the
disk
drive
is
write-protected,
the PROG.
NO./DATA
display wiil
show
"Pro".
Eject it from
the
drive,
cancel
write-protection
(See
page
4.),
put
it
back into
the
drive,
and then
continue.
If
you save
data
in
"Go"
method
and
there is
no memory
available
on the
disk, the
PROG,
NO./
DATA
display will
blink
showing
"FUL".
In
this
case,
press any
key
other than
the
REC key
to
stop the
blinking
and retry
with
another
disk.
If
during
saving
the
disk
memory
is
used
up, the PROG.
NO./DATA
display
will blink
showing
"con".
This
signals
that
the
data
saving
can
be
continued
using another
disk.
The
following
steps
are
explained
in
"Saving
and
Loading
Data Spanning
Several
Disks"
below.
The
memory
capacity
of
a
newly
formatted
2DD
disk is
equivalent
to
a
sample
of
approximate
1
2
seconds
whereas
that of
a 2HD
disk
is
equivaient
to a sample
of
approximately
25
seconds.
* Deleting
Files
in
the
Disk
1
.
Insert
the
disk into
the
disk
drive,
select
"DELETE"
in the
DISK
index in
Edit
mode,
and
press
the
REC
key.
The
PROG.
NO./DATA
display
will
show
a file
present
hi the disk.
When
no
files
are
present
on
the
disk,
the
display
shows
"—
".
If the
disk is
unformatted
or
incompatible
with the
S01
,
the
display
shows
"noF".
2.
Use
the data
entry
knob
to select
the
file
to be
deleted.
A
file
can
be
selected
and
deleted
by
file
type (ALL
or
SAMPLE).
An
individual
sample
in
an ALL
file
cannot
be
selected
and
deleted.
3.
Press
the
REC
key,
and
the
PROG.
NO./DATA
display
will
blink
showing that
file.
At this
time
make sure
the
desired
file
has
been
selected.
To
cancel
the
deleting
at this
point,
press any
key
other
than the
REC key.
When
a bank
key
is
pressed
you will
move
to
the
prior
step.
4.
Press
the
REC
key,
the
PROG.
NO./DATA
display
will
blink
showing "del".
To
continue,
press
the
REC
key
once
again.
The
display will
show
rapid
movement
during deleting
that
file.
When
deleting
is
completed,
the
SOI will
return
to step 1.
You
can
continue deleting
another file.
The
deleting
time
required
will vary
depending
on the
size
of the file.
If
the
disk in
the disk
drive
is
write-protected,
the
PROG.
NO./DATA
display will show "Pro".
Eject
it from
the drive,
cancel
write-protection
(See
page
4.)
,
put
it
back into
the drive, and
then
continue.
*
While
the disk
is
being
accessed
(the
disk
drive
LED
will
be lit)
,
do not turn off the
power or
attempt
removing
the disk
from
the
disk
drive.
This
will
damage
the
disk
as
well
as
the disk
drive.
42