ENGLISH
Introduction:
Please read this OWNER'S MANUAL thoroughly to familiarize yourself with each control and function.
We
at
ALPINE hope that your
new
KTP-190U will give you many years of listening enjoyment.
In
case of problems when installing your KTP-190U, please contact your authorized ALPINE dealer.
CAUTION:
These
controls
are
for
tuning
your
system.
Please
consult
your
authorized
Dealer
for
adjustment.
~WARNING
This symbol means important instructions.
Failure to heed them can result
in
serious injury or death.
~CAUTION
This symbol means important instructions.
Failure to heed them can result
in
injury or property damages.
~WARNING
•
DO
NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE.
Any fnnction that requires your prolonged attention should only be performed after coming to a
complete stop. Always stop the vehicle
in
a safe location before performing these fnnctions. Failure to do so may result
in
an
accident.
• KEEP THE VOLUME AT A LEVEL WHERE
YOU
CAN STILL HEAR OUTSIDE NOISES WHILE DRIVING.
Excessive volume levels that obscure sonnds such as emergency vehicle sirens or road warning signals
(train crossings,
etc.) can be dangerous and may result
in
an
accident. LISTENING AT LOUD VOLUME LEVELS IN A
CARMA
Y
ALSO CAUSE HEARING DAMAGE.
•
DO
NOT DISASSEMBLE
OR
ALTER. Doing so may result
in
an accident, fire or electric shock.
• USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may
result
in
fire, electric shock or other injury.
• USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result
in
fire or
electric shock.
•
DO
NOT BLOCK VENTS
OR
RADIATOR PANELS. Doing so may cause heat to build up inside and may result
in
fire.
•
MAKE
THE CORRECT CONNECTIONS. Failure to make the proper connections may result
in
fire or product
damage.
• USE ONLY
IN
VEHICLES WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.)
Failure to do so may result
in
fire, etc.
•
BEFORE WIRING, DISCONNECT THE
CABLE
FROM THE NEGATIVE BATTERY TERMINAL. Failure to do
so may
result
in
electric shock or injury due to electrical shorts.
•
DO
NOT ALLOW
CABLES
TO
BECOME ENTANGLED
IN
SURROUNDING OBJECTS. Arrange wiring and
cables
in
compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or
hang up on
places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.
•
DO
NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other
equipment. Doing so
will exceed the current carrying capacity of the wire and result
in
fire or electric shock.
•
DO
NOT DAMAGE PIPE
OR
WIRING WHEN DRILLING HOLES. When drilling holes
in
the chassis for
installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical
wiring. Failure to take such precautions may result
in
fire.
•
DO
NOT USE BOLTS
OR
NUTS IN THE
BRAKE
OR
STEERING SYSTEMS
TO
MAKE
GROUND
CONNECTIONS. Bolts
or nuts used for the brake or steering systems (or any other safety-related system), or
tanks
should NEVER be used for installations or ground connections. Using such parts could disable control of
the
vehicle and cause fire etc.
• KEEP
SMALL
OBJECTS SUCH AS BOLTS
OR
SCREWS OUT OF THE REACH OF CHILDREN. Swallowing
them may result
in
serious injury. If swallowed, consult a physician immediately.
~CAUTION
• HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage
to the product. Return it to your authorized
Alpine dealer or the nearest Alpine Service Center for repairing.
• HAVE THE WIRING
AND
INSTALLATION DONE
BY
EXPERTS. The wiring and installation of this unit requires
special technical skill and experience.
To
ensure safety, always contact the dealer where you purchased this
product to have the work done.
• USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified
accessory parts. Use of other than designated parts may damage this unit
internally or may not securely install
the unit
in
place. This may cause parts to become loose resulting
in
hazards or product failure.
•
ARRANGE THE WIRING SO IT IS NOT CRIMPED
OR
PINCHED
BY
A SHARP METAL EDGE. Route the
cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring.
If wiring passes through a hole
in
metal, use a rubber grommet to prevent
the wire's
insulation from being cut by the metal edge of
the
hole.
•
DO
NOT INSTALL
IN
LOCATIONS WITH HIGH MOISTURE
OR
DUST. Avoid installing the unit
in
locations
with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result
in
product
failure.
To Next Page
Loading...
