Amana NFW5800DW - User Manual

Questions and Answers

W
walshwilliamAug 15, 2025
What to do if the Amana Washer shows Lo FL or F8 E1 error?
- M
  Matthew RhodesAug 15, 2025
  If your Amana washer displays the error code Lo FL or F8 E1, it indicates a water supply problem. The unit will drain for 8 minutes, and the door will remain locked. Once this is complete, touch POWER once to clear the code, then touch POWER again to restart the washer. Ensure both hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned on. Check the inlet valve screens for clogs, remove any kinks in the inlet hose, and ensure auto shut-off connectors and hoses are properly installed and working. If the code reappears after these steps, it may require professional attention.
C
Christina RosalesAug 18, 2025
How to fix Amana Washer F9 E1 error?
- T
  taylor20Aug 18, 2025
  The F9 E1 error code on your Amana washer indicates a drain pump system issue. Check the plumbing to ensure the drain hose is correctly installed and not extending more than 41½" (114 mm) into the standpipe. Make sure the drain hose isn't kinked, pinched, or blocked, and remove any clogs. Use the drain hose form to securely attach it to the drainpipe or tub. Lower the drain hose if the end is higher than 96" (2.4 m) above the floor. Also, ensure you are using only HE detergent and measuring it according to the manufacturer's directions based on load size and soil level.
A
Amber WilliamsAug 21, 2025
Why does my Amana NFW5800DW show "Sd" (Excess suds)?
- J
  John WalkerAug 21, 2025
  The "Sd" code on your Amana washer indicates excessive suds. The washer is running a suds reduction routine. Allow the washer to continue its cycle. To prevent this in the future, only use HE detergent, measure the detergent carefully, and adjust the quantity based on the load size, following the detergent manufacturer's instructions.
N
Nicholas ManningAug 25, 2025
What to do if Amana NFW5800DW Washer displays F5 E2 error (door will not lock)?
- D
  David BlanchardAug 25, 2025
  If your Amana washer shows the F5 E2 error, it means the door isn't locking. Touch POWER to cancel the cycle. Ensure the door is completely closed and latched. Check for any items in the washer drum that might be preventing the door from closing fully.
D
Diana BrownAug 27, 2025
How to stop Amana Washer from vibrating?
- C
  christinedunnAug 27, 2025
  Excessive vibration in your Amana washer can be due to several reasons. Ensure the front and rear feet are in firm contact with the floor and locked, and that the washer is level. The jam nuts must be tight against the bottom of the cabinet. Check the floor for flexing or sagging; if uneven, a ¾" (19 mm) piece of plywood under the washer can help. Avoid tightly packing the load and avoid washing single items; balance single items like rugs or jackets with a few extra items.
K
ktaylorAug 30, 2025
Why is the Clean Washer LED flashing on my Amana Washer?
- H
  hallenAug 30, 2025
  The flashing Clean Washer LED on your Amana washer indicates that the washer has completed 30 wash cycles and is reminding you to run the affresh® Washer Cleaner cycle. To resolve this, run the affresh® Washer Cleaner cycle. If you choose not to run the cycle, the LED will stop flashing after 3 more regular wash cycles. After another 30 wash cycles, the reminder will reappear.
R
randall20Sep 2, 2025
What does "rL" mean on my Amana Washer display?
- I
  Ian CampbellSep 2, 2025
  The "rL" message on your Amana washer display means 'remove load'. It appears when a load is detected in the drum during the affresh® Washer Cleaner cycle. Remove the items from the washer drum and restart the Clean Washer with affresh® cycle.
C
Cindy McclainSep 5, 2025
Why does my Amana Washer display "nt" (interrupted)?
- J
  Julie BarnesSep 5, 2025
  The "nt" code on your Amana washer display indicates that the cycle was paused or cancelled. The washer can take 20 to 30 minutes to stop spinning and drain, and it will show this error code during that time. To clear the code, touch POWER once, then touch POWER again to restart the washer.
S
Sarah FloresSep 8, 2025
Why does Amana NFW5800DW Washer beep when START is touched?
- W
  Wesley SpearsSep 8, 2025
  If your Amana washer beeps when you touch START, it means the door is not completely closed. Make sure to close the door completely.
B
Bryan RodgersSep 12, 2025
What to do if Amana NFW5800DW Washer shows unknown F# E# code?
- P
  Paul FloydSep 12, 2025
  If your Amana washer displays an F# E# code other than those described, it indicates a system error. Touch POWER once to clear the code, then touch POWER again to restart the washer. If the code reappears, it may require professional attention.

Summary

Washer Safety

Safety Alert Symbol and Warnings

Explains the safety alert symbol and the meaning of DANGER and WARNING messages.

Important Safety Instructions

General Safety Precautions

Lists precautions to reduce risk of fire, electric shock, or injury.

Control Panel and Features

Control Panel Overview

Describes the layout and touch-sensitive nature of the control panel.

Cycle Status Lights Explained

Efficiency Monitor and Wash Settings

Using the Dispenser Drawer

Dispenser Drawer Operation

Details how to use the HE detergent, fabric softener, and bleach compartments.

Choosing the Right Detergent

Cycle Guide

Wash Cycle Descriptions

Details each wash cycle, its settings, and intended use.

Using Your Washer

Safety Warnings for Washer Use

Highlights fire and electrical shock hazards related to washer operation.

Preparing and Loading Laundry

Steps for sorting, preparing, and loading clothes into the washer.

Adding Laundry Products to Dispensers

Step-by-step guide for adding HE detergent, fabric softener, and bleach.

Selecting a Wash Cycle

Adjusting Cycle Settings

Starting and Pausing a Cycle

How to start, pause, and restart the wash cycle, including adding garments.

Washer Maintenance

General Washer Care Recommendations

Tips for keeping the washer clean and performing well, including detergent use and door position.

Cleaning the Inside of the Washer

Procedures for cleaning the inside using affresh or bleach.

Troubleshooting

Error Code Troubleshooting

Lists common error codes and their possible causes and solutions.

Vibration or Off-Balance Issues

Addresses causes and solutions for washer vibration and walking.

Water Leaks and Installation Checks

Covers issues related to water leaks and proper installation.

Washer Wont Run or Fill

Troubleshoots issues where the washer fails to start or fill.

Door Closure and Load Recommendations

Addresses issues related to the door not shutting properly or improper loading.

Washer Not Draining or Spinning

Solutions for when the washer fails to drain or spin properly.

Door Lock Issues

Load Not Rinsed Properly

Not Cleaning or Removing Stains

Improving Cleaning Performance

Addressing Odors

Preventing Fabric Damage

Controls Not Responding

Amana NFW5800DW Specifications

General

Style	front load
Color	white
Washer Capacity	4.2 cubic feet
Max Spin Speed	1200 revolutions per minute
Noise level	fasle
Internal Heater	no
Control Panel	analog
Delay Start / End	yes
Child Lock	no
Cycle Signal	yes
Interior Light	no
Smart Home	no
Annual Energy Consumption	109 kilowatt hours
Voltage	120 volts
Current	20 amperes