WARNING: These products may represent a possible shock or re hazard if improperly
installed or attached in any way. Products should be installed in accordance with these
instructions, current electrical codes, and/or the current National Electric Code (NEC).
Use this product only with its attached plug-in power cord. Any other power cord or
feed may damage the xture.
WARNINGS: READ ALL INSTRUCTIONS BEFORE YOU START:
CAUTION -
To reduce risk of re, electric shock, or injury to persons, pay close attention to
this manual and stay within its guidelines when using this product. Before use, note that this
product requires a 120V AC outlet. Ensure that the voltage of the power supply is compatible!
120V LED Hybrid 2 is cETLus Listed and interconnectable up to 150ft.
Safety rating is void if a kit is cut or altered, or if used with any power cord other than the one provided.
1. Do not cover this product as the covering may cause rope to overheat, melt, or ignite.
2. Do not operate Hybrid 2 while it is tightly coiled.
3. Do not submerge exible light in liquids, or use the product in the vicinity of standing water or other liquids.
4. Do not route the cord or Hybrid 2 through walls, ceilings, doors, windows, or any similar part of the building structure.
5. Secure this exible light using only the mounting clips provided or factory recommended mounting track (sold separately).
6. Do not secure this product or its cord with staples, nails, or like means that may damage the insulation.
7. Do not use if there is any damage to the PVC housing or power cord insulation. Inspect periodically.
8. Do not install on gates or doors, where subject to continuous exing.
9. Do not install in tanks or enclosures of any kinds.
10. Follow instructions carefully when splicing Hybrid 2 sections or attaching power cords. Ensure that all connections,
including the end cap on the last segment, are properly installed with dielectric grease and shrink tube to preclude the
entrance of water (outdoor applications).
11. Risk of re. Do not replace attachment plug. Discard product if attachment plug is damaged.
12. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock.
This plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does
not t, contact a qualied electrician. Never use with an extension cord unless plug can be fully inserted. Do not alter plug.
13. 120V Hybrid 2 is c/ETL/us Listed, but this safety rating is void if the 150ft reel is cut. Cutting the Hybrid 2 Kit and/or
altering the power cord in any ay including, but not limited to cutting, splicing, and/or adding any power accessories will
void the cETLus Listing.
14. This product is for decorative use only. Not to be used by children as a toy. Keep out of reach of small children.
15. Do not exceed 150ft maximum run distance in any single run.
CAUTION - To reduce the risk of re, electric shock, or injury to persons:
WARNING: When using outdoor portable lighting products, basic safety
precautions should always be followed to reduce the risk of re, electric shock,
and personal injury, including the following:
1. Use dielectric grease and shrink tube at all power connections, including end cap
when using outdoors.
2. Use ground fault circuit interrupter (GFCI) protection on the circuit(s) or outlet(s)
when using outdoors.
3. Use only UL approved outdoor extension cords, such as type SW, SOW, STW, STOW, SJW,
SJOW, SJTW, or SJTOW. This designation is marked on the jacket of the extension cord.
TO REPLACE FUSE (SEE FIGURE 1):
This plug contains an electrical fuse as a safety feature.
1. Disconnect power before replacing the fuse.
2. Grasp plug and remove from the receptacle or other outlet device.
3. Do not unplug by pulling on the cord.
4. Slide open the fuse access cover. See Figure 1.
5. Remove old fuse carefully.
6. Never attempt to replace the fuse with a higher wattage fuse. Use only 8 Amp
125 Volt fuse. Failure to do so may be a re hazard. (One spare fuse is included/
stored inside plug for convenience.)
7. Set new fuse in holder and close fuse access cover.
LED HYBRID 2 KITS
Installation instructions for H2-KITS Series
120V AC, 60Hz operation
RV1621
www.americanlighting.com
PAGE 1 OF 2
Figure 1
Do not operate Hybrid 2 while it
is tightly coiled.
Fuse is inside plug.
Slide open fuse access cover as shown.
To Next Page
Need help?
General
