American Standard SELECTRONIC 6065.121 - User Manual

SAVE FOR FUTURE USE
1
7301876-100
Product names listed herein are
trademarks of AS Americas Inc.
© AS Americas Inc. 2011
Putty Knife
Flush Valve
Sealant
Tape Measure
Regular Screwdriver
Adjustable Wrench
Carpenters Level
RECOMMENDED TOOLS AND MATERIALS
Pictures may not exactly define contour of china
Model 2282
BABY DEVORO FLUSHOMETER BOWL
Model 2282
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR HANDLING TO AVOID
BREAKAGE AND POSSIBLE INJURY!
NOTE: For proper operation product requires a minimum of 30 psi working line pressure
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
!
CLOSET
FLANGE
CLOSET
BOLTS
10"
254mm
WAX RING
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly
around waste flange (horn), with
tapered end of ring facing toilet. Apply a
thin bead of sealant around toilet base.
2
4
5
3
546mm
(21-1/2")
1 - 1/2
SPUD
121mm
(4-3/4")
254mm
(10")
FINISHED WALL
FINISHED
FLOOR
C/L OF OUTLET
1" N.P.T. OR 1" C.W.T. SUPPLY
TO FLUSH VALVE
INSTALLATION INSTRUCTIONS
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet
flange so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of
washers marked "THIS SIDE UP" must face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on
wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.)
c. Smooth off the bead of sealant around base. Remove excess sealant.
CLOSET FLANGE
CLOSET
BOLT
NUT
WASHER
BOLT
CAP
!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn
90°, and slide into place 6" (152mm) apart
and parallel to wall.
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard.com
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx

Summary

Baby Devoro Flushometer Bowl Installation

Recommended Tools and Materials

Lists necessary tools and materials for installing the toilet bowl.

Toilet Bowl Installation Steps

Step-by-step guide for physically installing the toilet bowl onto the flange.

Selectronic Flush Valve Overview and Preparation

Unpacking and Care Instructions

Procedures for unpacking, inspecting, and cleaning the flush valve.

Flush Valve Dimensions and Tools

Provides roughing-in dimensions, general description, and recommended tools.

Selectronic Flush Valve Installation Procedures

Flush Valve Installation Steps

Detailed guide for connecting the flush valve to the water supply and toilet.

Maintenance and Adjustments

Covers adjusting the stop valve, retrofitting, and replacing components.

Selectronic Flush Valve Operation and Troubleshooting

Battery and Power Pack Replacement

Instructions for replacing the standard battery or long-life power pack.

Setting Detection Range and Troubleshooting

Guide to setting the sensor detection range and troubleshooting common issues.

American Standard SELECTRONIC 6065.121 Specifications

General

Brand	American Standard
Model	SELECTRONIC 6065.121
Category	Plumbing Product
Language	English