Annovi Reverberi Blue Clean 955-965 User Manual (English)

Questions and Answers:

D
Duane BarnesJul 28, 2025
Why Annovi Reverberi Blue Clean 955-965 Pressure Washer pump does not reach working pressure?
- J
  john20Jul 28, 2025
  There are several reasons why your Annovi Reverberi Pressure Washer might not be reaching working pressure. It could be due to a worn nozzle, which requires replacement. Alternatively, the water filter might be fouled and needs cleaning. A low water supply pressure can also be the cause, so ensure the water supply tap is fully open. Check the tightness of hose fittings to prevent air from being sucked into the system. If there is air in the pump, switch off the appliance, depress and release the gun trigger until the water flows steadily, then switch the appliance back on. Finally, make sure the adjustable nozzle is positioned correctly; adjust it accordingly.
A
Amy CollinsAug 2, 2025
Why Annovi Reverberi Pressure Washer motor starts even with gun trigger is released?
- L
  Louis RobinsonAug 2, 2025
  If you have a TSS version of the Annovi Reverberi Pressure Washer and the motor starts even when the gun trigger is released, it might be due to a clogged nozzle, so you should clean it.
W
williamsnatalieAug 6, 2025
What to do if Annovi Reverberi Pressure Washer motor “sounds” but fails to start?
- J
  Jonathan MilesAug 6, 2025
  If your Annovi Reverberi Pressure Washer motor sounds like it's trying to start but doesn't, first ensure that the voltage of the mains power supply line matches what's indicated on the appliance's plate. Also, if you're using an extension cable, verify its characteristics to rule out voltage loss as the cause. If the appliance has not been used for a long period of time, you should contact your nearest Authorized Service Centre.
C
Christopher ReillyAug 10, 2025
Why does my Annovi Reverberi Blue Clean 955-965 pressure drop during use?
- J
  Jason CummingsAug 10, 2025
  If you're experiencing pressure drops during use with your Annovi Reverberi Pressure Washer, it could be because the water is being drawn from an external tank; try connecting the appliance to the mains water supply instead. Another cause might be that the intake water is too hot, so reduce the water temperature. A clogged nozzle could also be the culprit; in this case, you should clean the nozzle.
O
ochoajohnAug 15, 2025
What to do if Annovi Reverberi Blue Clean 955-965 Pressure Washer motor fails to start?
- M
  Melissa HayesAug 15, 2025
  If your Annovi Reverberi Pressure Washer motor isn't starting, begin by checking that the plug is firmly in the socket and that the mains voltage supply is present. If the appliance has not been used for a long period of time, try unjamming the motor from the hole at the rear of the appliance using the tool (L) (only in models with this feature).
L
Larry LutzAug 18, 2025
What to do if Annovi Reverberi Pressure Washer is noisy?
- S
  Scott KingAug 18, 2025
  If your Annovi Reverberi Pressure Washer is making excessive noise, the water might be too hot. Try reducing the water temperature.
M
Mark FerrellAug 23, 2025
What to do if Annovi Reverberi Blue Clean 955-965 has no water delivery when gun trigger is depressed?
- T
  Theresa RangelAug 23, 2025
  If your TSS version Annovi Reverberi Pressure Washer isn't delivering water when you depress the gun trigger (with the supply hose connected), the nozzle might be clogged. Try cleaning the nozzle.