Apec Water Ultimate Series User Manual

14
Fig. 11A
Details on Tubing Connections:
To ensure a smooth and correct installation, please connect the water lines following the se-
quence and order outlined below. Refer to Fig.11 & 11A for proper point locations.
1. Point Z Faucet connection:
Tubing color: Clear tubing. Connect the CLEAR tubing to the base of the RO faucet.
Fitting type: Quick Connect Fitting. Simply push Clear tubing into Quick Connect fitting. No Insert,
Sleeve or Nut needed here. (Attach threaded end of faucet adapter to the faucet metal
stem. No teflon tape needed here)
2. Point X Feed water connection:
Tubing color: Red tubing. Connect the RED tubing to the Feed Water Needle Valve.
Fitting type: Metal compression nut fitting.
See Fig.1B on page 4. Use plastic sleeve.
Add “insert” to tubing. No teflon tape here. Tighten nut with wrench.
Tips!
If Point X leaks after you have tightened the brass nut, check to make sure you did put the
plastic “insert and sleeve” onto the tubing. If the insert is already in place, then try
applying Teflon tape from the threaded metal stud all the way to the plastic tubing, wrap
the whole connection with 8-10 rounds of Teflon tape. Smooth out the tape on the
threaded part with your fingers. Tighten brass nut again. This should stop the leak.
If the plastic sleeve is damaged, you can use the metal sleeve, but you need to apply
Teflon tape as described above, this should stop the leak.
1
4
Fig. 11
A
Details on Tubing
Co
Co
nnnn
n
ec
ec
tions:
To ensure a smooth and correct installation, please connect the water lines
f
ollowing the s
e
-
quence and order
outlined below. Refer to
r
Fig.11
&
&
&
&
1
1
1A
1A
for proper point locations.
A
1.
P
P
oi
o
nt
Z
Fa
uc
et
c
on
ne
ct
io
n:
TuTu
bibi
b
n
ng
color: Clear tubi
ng
. Connect the
CL
L
EA
EA
R
R
tu
t
bi
ng
to the base o
f
the RO
f
aucet.
Fi
Fi
t
tt
ing type:
Q
uick Connect
F
i
tting.
Si
mp
mp
m
ly
y
push Clear tubing into Quick Connect
fi
fi
tt
tt
inin
g.g.
g
N
N
o Insert,
Sleeve or Nut needed
h
h
er
er
e.e.
.
(
(
At
A
tach threaded end o
f
f
aucet adap
te
e
r
r
toto
t
t
he
he
f
f
aucet metal
s
tem. No te
f
lon ta
pe
pe
nn
eeee
de
de
d here
)
2
.
P
o
int X Feed water
c
c
on
on
ne
ction
:
Tubing color
:
R
ed t
ub
ub
in
in
g.
g.
C
C
o
on
nect the RED tubing to the Feed Water
Ne
Ne
ed
ed
le Valve.
F
itting type:
M
etal
co
co
mp
mp
r
re
ssion nut
f
itting.
See
Fig.1B
on
page
4
.
Use
plastic sleeve.
Ad
d
“i
ns
er
t”
to tubing. No te
f
lon tape here. Tighten nut with wrench.
T
i
ps!
If
Point X leak
s
a
f
ter you have tightened the brass nut, check to make sure you did
pupu
t t
thth
e
e
pl
astic “insert and sleeve” onto the tubi
ng
. I
f
the insert is alrea
dy
in
pl
ace, then
tr
tr
y
y
applying
T
eflon tape from the th
re
re
ad
ad
a
ed metal stud all the way to the plastic tub
in
in
g,
g,
w
w
ra
ra
p
T
T
the whole connection with 8-
10
0
r
r
ouou
nd
n
s o
f
Te
f
lon tape. Smooth out the tape
on
on
t
t
hehe
threaded part with your
f
i
ng
ng
er
er
s.s.
TT
T
ig
ig
hten brass nut again. This should st
op
p
t
t
he
he
l
l
e
ea
k
k.
If
the plastic sleeve
is
dd
am
am
ag
ag
ed, you can use the metal sleeve, but
yo
yo
u
u
nene
ed
ed
to apply
Te
f
lon tape as des
cr
cr
c
ibib
eded
e
above, this should stop the leak.

Apec Water Ultimate Series Specifications

General

Brand	Apec Water
Model	Ultimate Series
Category	Water System
Language	English