Apex Digital 9S-010500

Questions and Answers

J
jeffersonryanSep 18, 2025
What to do if my Apex Digital 9S-010500 Control Unit is showing Error E101-07?
- T
  Taylor MooreSep 18, 2025
  If the device displays error E101-07, check for any damage in cable connections related to the heating humidifier. If the issue persists, replace the heating plate. If it still remains, replace the heating humidifier mainboard.
E
Emily LewisAug 25, 2025
Why is there no air flow through the mask of my Apex Digital 9S-010500 Control Unit?
- B
  bhartAug 25, 2025
  If there's no air flow through the mask, first, check that the power cord is properly connected and the device is turned on. Next, ensure the heated tubing is correctly connected. Finally, check for and unblock any obstructions in the air tubing.
M
Matthew WilkersonAug 25, 2025
Why is my Apex Digital 9S-010500 showing 'Low P icon'?
- P
  paul31Aug 26, 2025
  The 'Low P icon' may appear if the mask isn't properly fitted. Make sure the mask fits securely on your face. Also, check the tubing for any damage and ensure it's properly connected. Inspect the pressure and flow sensor tubes to confirm they are correctly connected.
W
William PowellAug 26, 2025
What to do if my Apex Digital Control Unit displays no display or incorrect display?
- R
  reyesjohnAug 27, 2025
  If there is no display or an incorrect display, check if the power cord is connected to the power socket. If it is, the issue may be due to LCD or controlled PCB failure, in this case replace the LCD. If the problem persists, replace the mainboard.
S
Susan WhiteSep 19, 2025
What to do if my Apex Digital Control Unit is showing Error E101-08?
- C
  Connor FloresSep 22, 2025
  If error E101-08 appears, reconnect the heated humidifier. If the problem persists, replace the heating plate. If the issue still remains, replace the humidifier mainboard.
E
Erin RamirezSep 23, 2025
Why date cannot be copied to the SD card of my Apex Digital 9S-010500?
- K
  Kristen ChurchSep 23, 2025
  If data cannot be copied to the SD card, check if the SD card is provided by APEX or check the SD card format (FAT32). Also, verify if the SD card is full and clear space for new data. If the issue persists, the data on the SD card may be corrupted; format the card or use a new SD card.
G
Gloria BarnesSep 9, 2025
What to do if my Apex Digital Control Unit is showing Error E101-01?
- S
  Sarah CampbellSep 9, 2025
  If error E101-01 is displayed, first reset the device. If the problem remains, the mainboard may need to be replaced.
D
Daniel SmithSep 12, 2025
What to do if my Apex Digital 9S-010500 is showing Error E100-002?
- T
  Tara EnglishSep 12, 2025
  If the device shows error code E100-002, restart it. After restarting, enter the Setting mode and select About to verify if the software version is displayed. If the problem persists, the 4G module may need to be replaced.
K
Kenneth JacksonSep 3, 2025
What to do if my Apex Digital 9S-010500 is showing Error 002?
- D
  Destiny LeonardSep 3, 2025
  If Error 002 is displayed, verify the SD card format is FAT32. Also, ensure the SD card is properly inserted into the slot and has sufficient capacity. If the problem persists, consider replacing the SD module.
T
Tammy TaylorSep 1, 2025
What to do if my Apex Digital Control Unit is showing Error 006?
- A
  Amy BishopSep 1, 2025
  If your device displays Error 006, ensure the cellular setting is turned on. If the signal remains weak, try replacing the 4G SIM card. Also, verify that the antenna connects to the 4G module board. If the problem persists, replace the 4G module board.