What to do if Apex Digital STURDY SA-300MB Laboratory Equipment shows an emergency stop?
If the EMERGENCY button was pressed to interrupt the program, wait until the pressure reading is at 0. Then, press the “unlock button” to open the door by turning the door knob 90° counterclockwise. It is recommended to verify the sterility of the sterilized items again.
Why does my Apex Digital STURDY SA-300MB say maintenance service is required?
The message 'Maintenance service' is displayed because the default 5,000 cycles or the preset service cycles have been reached. You can press any key to continue your operation, but this message will be displayed every time to remind you of the service requirement.
What to do if Apex Digital Laboratory Equipment displays 'Chamber temp >97?'?
Please wait until the chamber temperature cools down. Then, press any key to continue. Your sterilization work will start automatically after the preset time is reached.
Defines Danger, Warning, and Caution hazard levels for user safety.
Alerts on electrical, flammable, child, and pressure-related hazards during operation.
Precautions for power, heat, carrying, and general handling during maintenance.
Explains symbols for caution, earth, WEEE, manufacturer, and other regulatory marks.
Explains symbols for power, status, and operation buttons.
Instructions for unpacking and retaining packaging materials.
Specifies installation site conditions and initial setup steps.
Details on draining waste and connecting water supply.
Step-by-step guide for installing internal sterilizer parts.
Technical details for SA-300MB/SA-302MB models and power.
Defines the purpose and suitable loads for the sterilizer.
Identifies external and internal parts of the sterilizer.
Overview of available sterilization programs like Standard, PRION, LIQUID.
Visual guides for running sterilization cycles.
Steps for preparing and running sterilization cycles.
Instructions for Leakage, Helix, and B&D tests.
How to adjust date, time, language, units, and other settings.
Guide for printer use and SD card data management.
Covers emergency stop and item placement for sterilization.
Lists error codes and solutions for system-level issues.
Lists error codes and solutions for specific component failures.
Lists error codes and solutions related to sterilization cycle steps.
Lists error codes and solutions specific to test procedures.
Lists error codes and solutions for SD card or printer issues.
Provides solutions for common symptoms and problems.
Routine checks and cleaning tasks for daily upkeep.
Tasks to be performed on a weekly basis.
Tasks to be performed on a monthly basis.
Tasks for yearly service, often by a technician.
How to use biological indicators for validation.
Procedure for performing the Bowie-Dick test.
Detailed steps for conducting the Helix test.
Defines Danger, Warning, and Caution hazard levels for user safety.
Alerts on electrical, flammable, child, and pressure-related hazards during operation.
Precautions for power, heat, carrying, and general handling during maintenance.
Explains symbols for caution, earth, WEEE, manufacturer, and other regulatory marks.
Explains symbols for power, status, and operation buttons.
Instructions for unpacking and retaining packaging materials.
Specifies installation site conditions and initial setup steps.
Details on draining waste and connecting water supply.
Step-by-step guide for installing internal sterilizer parts.
Technical details for SA-300MB/SA-302MB models and power.
Defines the purpose and suitable loads for the sterilizer.
Identifies external and internal parts of the sterilizer.
Overview of available sterilization programs like Standard, PRION, LIQUID.
Visual guides for running sterilization cycles.
Steps for preparing and running sterilization cycles.
Instructions for Leakage, Helix, and B&D tests.
How to adjust date, time, language, units, and other settings.
Guide for printer use and SD card data management.
Covers emergency stop and item placement for sterilization.
Lists error codes and solutions for system-level issues.
Lists error codes and solutions for specific component failures.
Lists error codes and solutions related to sterilization cycle steps.
Lists error codes and solutions specific to test procedures.
Lists error codes and solutions for SD card or printer issues.
Provides solutions for common symptoms and problems.
Routine checks and cleaning tasks for daily upkeep.
Tasks to be performed on a weekly basis.
Tasks to be performed on a monthly basis.
Tasks for yearly service, often by a technician.
How to use biological indicators for validation.
Procedure for performing the Bowie-Dick test.
Detailed steps for conducting the Helix test.
General| Brand | Apex Digital |
|---|---|
| Model | STURDY SA-300MB |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
