ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT(S).
This instruction manual complies with the Treestand Manufacturers Association’s TMS 04 - Standard Practice for Treestand Instructions and TMS 02 - Standard Test Method for Treestand Fall Arrest Systems.
16
STEP 10.
(STEPS 8 through 10) to climb to
the desired hunting/use height. It
is of the utmost importance that
you remember to raise the full-
body fall arrest harness tether/tree
belt up each time you climb higher.
WARNING! NEVER adjust
the length of the climbing cable
or attempt to level either the
seating or standing platforms at
heights above ground-level. All
adjustments must be made at
ground-level. Failure to follow
these instructions may result in
serious injury or death!
STEP 11.
hunting/use height, with the seating
and standing platforms level and at
a comfortable height apart, remove
the
ratchet strap with D-ring
from the accessory bag and
holes in the
.
STEP 13.
Snap Pin
Fig 1 Fig 2
Fig 3
Fig 4
Fig 5
Fig 7A Fig 7B
Fig 8A Fig 8B
Fig 10
FIGURE 2
4
3
RATCHET STRAP INSTRUCTIONS
STEP 1. Thread strap
through slot in the center of
the ratchet reel. (see Fig. 1)
Remove slack from strap by
pulling loose end as tightly
as possible. (see Fig. 2)
STEP 2. Then ratchet handle
back and forth to tighten
straps, a minimum of two (2)
wraps around the ratchet reel is required. (see Fig. 3)
STEP 3. After strap is tight, close handle to the lock position.
STEP 4. To remove tension, pull spring loaded retaining lock and open ratchet completely, then manually pull strap to loosen. (see Fig. 4)
FIGURE 1
2X Min.
1 3
CAM-BUCKLE INSTRUCTIONS
Insert the long strap through buckle on short strap and pull tight to
secure.
2
FIGURE FIGURE FIGURE
FIGURE 2
4
3
RATCHET STRAP INSTRUCTIONS
STEP 1. Thread strap
through slot in the center of
the ratchet reel. (see Fig. 1)
Remove slack from strap by
pulling loose end as tightly
as possible. (see Fig. 2)
STEP 2. Then ratchet handle
back and forth to tighten
straps, a minimum of two (2)
wraps around the ratchet reel is required. (see Fig. 3)
STEP 3. After strap is tight, close handle to the lock position.
STEP 4. To remove tension, pull spring loaded retaining lock and open ratchet completely, then manually pull strap to loosen. (see Fig. 4)
FIGURE 1
2X Min.
1 3
CAM-BUCKLE INSTRUCTIONS
Insert the long strap through buckle on short strap and pull tight to
secure.
2
FIGURE FIGURE
CLIMBING DOWN:
WARNING!
Prior to attempting to use this or any other
up and using this product(s) at ground-level prior to attempting to use
product(s)
setup, installation and use at ground-level - you’re now ready to use it
at heights above ground-level. Failure to follow these instructions may
result in serious injury or death!
WARNING!
STOP NOW!!!!!
API
full-body fall arrest harness and it is still attached to the tree
to follow these instructions may result in serious injury or death!
WARNING!
DO NOT bounce or jump on any portion of the climbing treestand in an attempt to seat it to the tree. Failure to follow these
instructions may result in serious injury or death!
WARNING!
NEVER adjust the length of the climbing cable or attempt to level either the seating or standing platforms at heights above ground-
level. All adjustments must be made at ground-level. Failure to follow these instructions may result in serious injury or death!
STEP 1.
WARNING!
NEVER
in serious injury or death!
To Next Page
Loading...